Loading ...
Loading ...
3
models the maximum allowed
water temperature is 60°C.
Do not cut hoses and, in the
case of appliances fitted with a
waterstop system, do not
immerse the plastic casing
containing the inlet hose in
water.
If hoses are not long enough,
contact your local dealer.
Make sure the inlet and drain
hoses are kink-free and are not
crushed. Before using the
appliance for the first time,
check the water inlet and drain
hose for leaks.
During use, the access to the
rear wall should be limited in a
sustainable manner such as
approaching the device to the
wall or furniture board.
When installing the appliance
make sure that the four feet are
stable and resting on the floor,
adjusting them as required, and
check that the appliance is per-
fectly levelled using a spirit level.
If installing the appliance at the
end of a row of units making the
side panel accessible, the hinge
area must be covered to
prevent risk of crushing.
For dishwashers having
ventilation openings in the
base, the openings must not be
obstructed by a carpet.
Use the appliance only when the
covers shown on diagram 15 in
the installation booklet are cor-
rectly assembled - risk of injury.
ELECTRICAL WARNINGS
For installation to comply with
current safety regulations, an
omnipolar switch with minimum
contact gap of 3mm is required
and the appliance must be
earthed.
If the power cable is damaged,
replace with an identical one.
The power cable must only be
replaced by a qualified
technician in compliance with
the manufacturer instruction
and current safety regulations.
Contact an authorized service
centre. If the fitted plug is not
suitable for your socket outlet,
contact a qualified technician.
The power cable must be long
enough to connect the
appliance, once fitted in its
housing, to the main power
supply. Do not pull the power
supply cable.
Do not use extension leads,
multiple sockets or adapters.
Do not operate this appliance if
it has a damaged mains cord or
plug, if it is not working
properly, or if it has been
damaged or dropped. Keep the
cord away from hot surfaces.
The electrical components
must not be accessible to the
user after installation. Do not
touch the appliance with any
wet part of the body and do not
operate it when barefoot.
ELECTRICAL CONNECTION
FOR GREAT BRITAIN AND
IRELAND ONLY
Fuse replacement.
If the mains lead of this
appliance is fitted with a BS
1363A 13amp fused plug, to
change a fuse in this type of
plug use an A.S.T.A. approved
fuse to BS1362 type and
proceed as follows:
1. Remove the fuse cover (A)
and fuse (B).
2. Fit replacement 13A fuse into
fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted
when changing a fuse and if the
fuse cover is lost the plug must
not be used until a correct
replacement is fitted.
Correct replacement are
identified by the colour insert
or the colour embossed in
words on the base of the plug.
Replacement fuse covers are
available from your local
electrical store.
For the Republic of Ireland only
The information given in
respect of Great Britain will
frequently apply, but a third
type of plug and socket is also
used, the 2-pin, side earth type.
Socket outlet / plug
(valid for
both countries)
If the fitted plug is not suitable
for your socket outlet, please
contact After-sales Service for
further instruction. Please do
not attempt to change plug
yourself. This procedure needs
to be carried out by a qualified
technician in compliance with
the manufactures instructions
and current standard safety
regulations.
CORRECT USE
The water in the dishwasher is
not potable.
The maximum number of place
settings is shown in the product
sheet.
The door should not be left in
the open position since this
could present a tripping hazard.
The open dishwasher door can
only support the weight of the
loaded rack when pulled out.
Do not rest objects on the door
or sit or stand on it.
Use only detergent and rinse
additives designed for an
automatic dishwasher.
B
A
EN
Loading ...