Loading ...
Loading ...
Operation Guide 5338
E-20
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use D (East) to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about two seconds.
This toggles the city code you selected in step1
between Daylight Saving Time (DS T indicator
displayed) and standard time (DS T indicator not
displayed).
You cannot use the World Time Mode to change the DST setting of the city
currently selected as your Home City in the Timekeeping Mode.
Note that you cannot switch between standard time/daylight saving time (DST)
while UTC is selected as the World Time City.
The standard time/daylight saving time (DST) setting affects only the currently
selected time zone. Other time zones are not affected.
DST indicator
E-21
Using the Alarm
You can set fi ve independent daily alarms. When a
daily alarm is turned on, an alarm tone will sound
for about 20seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. One
of the alarms is a snooze alarm, while the other four
are one-time alarms. The snooze alarm operation will
repeat every fi ve minutes, up to seven times.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
Alarm number
Alarm time (Hour : Minutes)
E-22
To enter the Alarm Mode
Use C to select the Alarm Mode as shown on page E-9.
The snooze alarm screen is indicated by SNZ, while the other alarm screens are
numbered AL1 through AL4. The Hourly Time Signal screen is indicated by SIG.
When you enter the Alarm Mode, the data you were viewing when you last exited
the mode appears fi rst.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
AL1 AL3 SNZAL2 AL4 SIG
D D DD D
D
Alarm ON/OFF indicator
Alarm indicator
E-23
2. Hold down A for about two seconds until the alarm time starts to fl ash. This is
the setting mode.
3. Press C to move the fl ashing between the hour and minute settings.
4. While a setting is fl ashing, use D (+) and B (–) to change it.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting mode.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-24
To turn an alarm and the Hourly Time Signal on and off
In the Alarm Mode, use D to select an alarm or the
Hourly Time Signal.
When the alarm you want or the Hourly Time Signal
is displayed, press A to toggle it between on (“
”
displayed) and off (“
” displayed).
The alarm on indicator (when any alarm is on), snooze
alarm indicator (when the snooze alarm is on), and the
Hourly Time Signal on indicator (when the Hourly Time
Signal is on) are shown on the display in all modes.
To stop the alarm
Press any button.
Hourly time signal
on indicator
Snooze alarm indicator
E-25
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use C to select the Stopwatch Mode as shown on
page E-9.
1/100 Seconds
Split
Seconds
Hours
Minutes
E-26
To perform an elapsed time operation
D
D D D A
Start Stop (Restart) (Stop) Reset
To pause at a split time
D
A A D A
Start Split
(SPL displayed)
Split release Stop Reset
To measure two fi nishes
D
A D A A
Start Split
(SPL displayed)
First runner fi nishes.
Display time of fi rst
runner.
Stop
Second runner
fi nishes.
Split release
Display time of
second runner.
Reset
E-27
Note
The Stopwatch Mode can indicate elapsed time up to 23hours, 59minutes,
59.99seconds.
Once started, stopwatch timing continues until you press D to stop it, even if
you exit the Stopwatch Mode to another mode and even if timing reaches the
stopwatch limit defi ned above.
Exiting the Stopwatch Mode while a split time is frozen on the display clears the
split time and returns to elapsed time measurement.
E-28
Countdown Timer
The countdown timer can be set within a range of
one minute to 24hours. An alarm sounds when the
countdown reaches zero.
To enter the Countdown Timer Mode
Use C to select the Countdown Timer Mode as shown
on page E-9.
Seconds
MinutesHours
E-29
To confi gure the countdown timer
1. While the countdown start time is on the display in
the Countdown Timer Mode, hold down A until the
current countdown start time starts to fl ash, which
indicates the setting mode.
If the countdown start time is not displayed, use the
procedure under “To perform a countdown timer
operation” (page E-30) to display it.
2. Press C to move the fl ashing in the sequence shown
below to select other settings.
Start Time (hours) Start Time (minutes)
C
Loading ...
Loading ...