User Manual LG 50NANO866PA Nano86 50 inch 4K NanoCell TV

• Owner's manual - (English)

Table of contents

• Preparing
• Lifting and moving the TV
• Mounting on the Table
• Mounting to the Wall
• Starting TV
• Registering Magic Remote Control
• Using Remote Control
• Connections
• Troubleshooting
• Specifications

Preparing

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material that the TV originally came in.
• Before moving or lifting the TV. disconnect the power cord and all cables.
• When holding the TV. the screen should face away from you to avoid damage.

• Hold the side and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

• Use at least two people to move a large TV.
• When transporting the TV by hand. hold the TV as shown in the following illustration.

• When transporting the TV. do not expose the TV to jolts or excessive vibration.
• When transporting the TV. keep the TV upright; never turn the TV on its side or tilt towards the left or right.
• • Do not apply excessive pressure to cause flexing / bending of frame chassis as it may damage screen.
• When handling the TV. be careful not to damage the protruding buttons.

• Avoid touching the screen at all times. as this may result in damage to the screen.
• When attaching the stand to the TV set. place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

Mounting on the Table

1. Lift and tilt the TV into its upright position on a table.

• Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

2. Connect the power cord to a wall outlet.

• Do not apply foreign substances (oils. lubricants. etc.) to the screw parts when assembling the product. (Doing so may damage the product.)
• If you install the TV on a stand. you need to take actions to prevent the product from overturning. Otherwise. the product may fall over. which may cause injury.
• Do not use any unapproved items to ensure the safety and product life span.
• Any damage or injuries caused by using unapproved items are not covered by the warranty.
• Make sure that the screws are fastened tightly. (If they are not fastened securely enough. the TV may tilt forward after being installed.)
• Do not fasten the screws with excessive force otherwise they may strip and become loose.

Securing TV to the Wall

1. Insert and tighten the eye-bolts. or TV brackets and bolts on the back of the TV.

• If there are bolts inserted at the eye-bolts position. remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

• Use a platform or cabinet that is strong and large enough to support the TV securely.
• Brackets. bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

Stand

(Depending upon model)

• AP-G1DV55 OLED55G1*
• AP-G1DV65 OLED65G1*
• AP-G1DV77 OLED77G1*

Mounting to the Wall

Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. We recommend the use of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with cables connected. When you do not use LG’s wall mount bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. It is advised to connect all the cables before installing fixed wall mounts.

• Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.
• For more information of screws and wall mount bracket, refer to the Separate purchase.
• If you intend to mount the product to a wall. attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts). fix it carefully so as not to drop.
• When mounting a TV on the wall. make sure not to install the TV by hanging the power and signal cables on the back of the TV.
• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.
• When installing the Full Contact Wall Mount, the TV may not be contacted firmly against the wall due to some wall conditions.

Wall Mounting Bracket

(Depending on model)

Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.

For more information, watch the installation video on your smart device.

Precautions for Safety

(Except for OLW480B)

• Professional installers should read this manual carefully to ensure proper installation.
• Professional installers should forward this manual to customers after installation and encourage them to read and store it in a convenient place for future reference.

After reading the installation manual, keep it in a convenient place for future reference.

• Ask a professional installer appointed by the store for installation of the product.
• Installation by someone other than a professional installer is extremely dangerous and may result in personal injury.
• Do not install the product in an unstable site that cannot withstand its weight.
• If the installation site lacks sufficient rigidity, the product may fall and cause personal injury.
• Contact a professional installer appointed by the store prior to moving or replacing the product after installation.
• Installation is a technical task and safety issues may arise if an individual attempts to install or move the product personally.
• Do not hang on the product or subject it to severe impact after installation.
• Doing so may cause the product to fall and cause personal injury.
• When installing the product on a wall, do not hang the power line or signal cables from the back of the TV.
• This can damage the cords, resulting in a fire, electrical shock or malfunction of the product.
• Be sure to wear work gloves when installing the product.
  • Installing with unprotected hands may result in injury.
• Install the product according to the instructions in the installation manual.

Failure to install the product according to the instructions in the installation manual can result in serious personal injury or product damage.

• Be sure to have at least two people when installing the product or adjusting the product’s height.
• Attempting to perform installation or adjustments personally may result in personal injury or damage to the product.
• Make sure a wall is available prior to proceeding with installation. Make use of the anchors and screws provided with the product.
• Use of any unauthorized anchors or screws may not support the product’s weight, which poses safety risks.
• When drilling in the wall for installation, be sure to use drill bits and drills of the specified diameter. Follow the instructions for the hole depth.
• Drilling and installing the product in ways other than specified in the installation manual may result in an unstable installation and potential safety issues.
• Do not wipe the product with a wet towel or use any heating equipment or humidifier under the place where the product is installed.
• Liquid water or vapor may enter the product and excessive heat may cause fire, electric shock, or malfunction.
• Do not install the product near a fire sprinkler or detector, a place where vibration or shock may occur or near a high-voltage wire or power source.
• Unplug the product’s power cord from the wall outlet before installing.
• Installing the product while the power cord is plugged in may result in electric shock or fire.
• Do not install the product with bare hands. Be sure to wear work gloves.
• Attempting installation without work gloves may cause personal injury.
• Connect the product with the supplied cable. Use of an unauthorized cable may result in damage by friction with the wall. Make sure to use the supplied cable gender. (This may vary by model.)

Before Installation

(Except for OLW480B)

• Do not use the product for any purpose other than installing the TV on a wall.
• Avoid product damage and safety accidents caused by careless installing or use of improper or unauthorized wall mount.
• Follow the instructions in the installation manual for a convenient installation of the wall mount.
• Immediately discontinue installation and contact the service centre if you cannot fully understand the installation process.
  Use a professional installer if any installation issues remain after the inquiry.
• Installation of this product on a concrete wall or wood stud is recommended. Installation of this product on other surfaces (Dry wall, plywood, bricks, etc.) is not recommended. Improper installation may result in the product falling.
• Install the product only on a vertical wall.
  Do not install on a tilted wall that exceeds building standards or on the heavily titled wall or ceiling.
  LG is not responsible for problems caused by improper installation of the product, e.g., heavily tilted walls and ceilings.
• Check the enclosed accessories before installation. We are not responsible for any lost or damaged accessories after the inner packaging is opened.
• When an infant or small child swallows the enclosed accessories, various safety accidents such as choking may occur. Keep the enclosed accessories out of the reach of infants and children.
• When tightening screws, tighten until fully snug.
• Avoid using excessive force when tightening the screws. Doing so may damage the wall and product or reduce the rigidity or performance of the product.
• Avoid installing a TV that exceeds the specified tensile load, and do not allow any external force to be applied to the product.
• Avoid accidents by using work tools with care during installation.

Tools for Installation

• “+” shaped screwdriver (manual or electric) / level / drill / Ø 8 mm drill bit for concrete or Ø 4 mm drill bit for steel

Antenna/Cable

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs
• •If the image quality is poor, install a signal amplifier properly to improve the image quality.
• If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.
• An antenna cable and converter are not supplied
• For a location that is not supported with ULTRA HD broadcasting, this TV cannot receive ULTRA HD broadcasts directly.

Satellite dish

Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω). (Depending on model

Starting TV

Turning on the TV

You can simply operate the TV functions, using the button.

Using button

Power On (Press)

Power Off1) (Press and Hold)

Menu Control (Press)

Menu Selection (Press and Hold)

1. All running apps will close, and any recording in progress will stop. (Depending on country)
2. You can access and adjust the menu by pressing the button when TV is on.
3. You can use the function when you access menu control.

Note: If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust the Menu items using the button.

Note

• Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
• The available menus and options may differ from the input source or product model that you are using.
• New features may be added to this TV in the future.
• The device must be easily accessed to a location outlet near the access. Some devices are not made by turning on / off button, turning off the device and unplugging the power cord.

Inserting the battery

When the message [Magic Remote battery is low. Please change the battery.] is displayed, replace the battery. To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching the and ends to the label inside the compartment, and close the battery cover.

Registering Magic Remote Control

How to register the Magic Remote Control

To use the Magic Remote, first pair it with your TV.

1. Put batteries into the Magic Remote and turn the TV on.
2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.
   * If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control

Press the (Back) and (Home) buttons at the same time, for five seconds, to unpair the Magic Remote with your TV. * Press and hold the (Home) and (Q. Settings) buttons for more than 5 seconds to disconnect and re-register the Magic Remote at the same time.

Connecting Smart Devices using NFC Tagging

Using the NFC Feature NFC is technology that uses Near Field Communication, allowing you to conveniently send and receive information without separate settings. By bringing a smart device near the NFC-enabled remote control, you can install the LG ThinQ app and connect the device to the TV.

1. Turn on NFC in the smart device’s settings. To use NFC with Android devices, set the NFC option to enable ‘read/write tags’ in the smart device’s settings. The NFC settings may vary depending on the device.
2. Bring the smart device near the (NFC) on the remote control. The required distance for NFC tagging is about 1 cm
3. Follow the instructions to install the LG ThinQ app on your smart device.
4. Retagging the smart device to the remote control allows you to conveniently access various features on the connected TV through the LG ThinQ app

Using Remote Control

Using Magic Remote Control

The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly

Connections

Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device.

HDMI

• When connecting the HDMI cable, the product and external devices should be turned off and unplugged.
  
• Supported HDMI Audio format (Depending on model):

True HD (48 kHz),

Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz),

PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

Note If the device connected to Input Port also supports HDMI Deep Colour, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Deep Colour] setting to off.

• → [General] → [Devices] → [HDMI Settings] → [HDMI Deep Colour]
  • On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0), 4K @ 100/120 Hz (4:4:4, 4:2:2, 4:2:0)
  • Off: Support 4K @ 50/60 Hz (4:2:0)
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.
• Recommended HDMI Cable Types
  • Ultra High Speed HDMI®/™ cable (3 m or less)

USB

Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the USB port on the TV directly.

Note For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick, 18 mm width and 8 mm a wire diameter. Use an extension cable that supports or higher if the USB cable or USB memory stick does not fit into your TV’s USB port.

• A ≦ 10 mm
• B ≦ 18 mm
• C ≦ 8 mm

IR Blaster

Control the set-top box (cable/satellite/IP/OTT), Blu-ray/DVD player, soundbar, game consoles, etc., using the IR Blaster. (Depending on country)

Note

• Connect the IR Blaster cable to the TV’s IR Blaster port.
• Place both ends (one or two) of the IR Blaster in front of the external device as shown in the picture below.
• Use universal control settings to control the device. Go to → [General] → [Devices] → [External Devices] → [Universal Control Settings].
• Secure the IR Blaster with the 3M tape provided.

CI module

View the encrypted (pay) services in digital TV mode. (Depending on model)

Note

• Check if the CI module is inserted into the in the right direction. If the module is not inserted properly, this can cause damage to the TV and the .
• If the TV does not display any video and audio when CI+ CAM is connected, please contact to the Terrestrial/Cable/Satellite Service Operator.

External Devices

Available external devices are: Blu-ray player, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.
Note

• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of the TV port.
• If you record a TV programme on a Blu-ray/DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the connected device.
• Refer to the external equipment’s manual for operating instructions.
• If you connect a gaming device to the TV, use the cable supplied with the gaming device.
• In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the [Picture] menu until the picture is clear.
• In PC mode, some resolution settings may not work properly depending on the graphics card.
• If Ultra HD content is played on your PC, video or audio may become disrupted intermittently depending on your PC’s performance. (Depending on model)
• When connecting via a wired LAN, it is recommended to use a CAT 7 cable. (Only when port is provided.)

Troubleshooting

Specifications

(Depending on country)