Loading ...
Loading ...
Loading ...
Installation of oven and
connection with cooking
hob
1 - Oven preparation:
2 - Preparation of cooking hob:
a) Check type of gas:
Check that the appliance leaves the factory
with the type of gas it requires. If it does
not, the burner tips will need to be changed
and the minimum point of the tap fittings
adjusted. (See section Changing gas type
in these instructions).
b) Check the insertion situation:
Kitchen unit and distances to the insertion
space.
Put these instructions in a safe place for future reference
Remove the oven knobs. Fig. 7
4 - Electrical connection
Connect the oven to the mains.
3 - Installation of cooking hob
If the cooking hob has not yet been inserted
into its space, place it there and make
sure it has been secured to the unit. Also
connect the gas as previously described.
Raise and secure the universal joints to
the bottom of the cooking hob with the
help of adhesive tape or gum, if the cooking
hob does not have this.
en
Instructions for
the installation technician
to be cut in the kitchen unit.
The panels on the work surface, in the
be made of non-flammable material.
used to secure it should be heat resistant,
to prevent deterioration.
Electrical cables must not come into
contact with hot areas.
The power cable must be secured to the
kitchen unit to prevent it from touching any
hot parts of the oven or the cooking hob.
components must be earthed.
Read these instructions before installing
or using the appliance.
IN THE EVENT THAT THESE
RECOMMENDATIONS ARE NOT
OBSERVED, THE INSTALLATION
TECHNICIAN WILL BE RESPONSIBLE
FOR ANY DAMAGE CAUSED, AND THE
MANUFACTURER WILL BE EXEMPT
FROM ALL RESPONSIBILITY.
Installing the cooking
hob in the kitchen unit
The option of locating the cooking hob in
the kitchen unit (in accordance with gas
Insertion measurements
appropriate sized cut in the work
surface.
Figure 1.
For installation over an oven, check the
dimensions of the oven according to your
assembly manual.
If while using a hob with a control
module it was possible to access its lower
part, a separator will be needed in order
to avoid possible contact. The minimum
become damp they expand quite rapidly.
the watertight seal (underside of the
cooking hob) may already be fitted; if this
circumstances remove them.
The seal ensures that the entire work
surface will be watertight, and prevents
water seepage.
If they are not fitted, remove the pan
supports, the burner covers and the
diffusers of the cooking hob and place the
hob upside down, and put the adhesive
seal supplied with the appliance on the
underside of the cooking hob Fig. 2.
3 - Remove the clips from the accessory
bag provided.
Depending on the appliance model, your
type of clamp may be similar to the one
shown in Fig. 3 or Fig. 4.
- If your type of clamp is the same as
the one illustrated in Fig. 3:
Place them in the holes designed for
this.
Insert and simultaneously press the ends
so that the cooking hob is supported
uniformly on its perimeter.
If you need to disassemble the
appliance, simply push it upwards from
underneath.
- If your type of clamp is the same as
the one illustrated in Fig. 4:
Screw them to the points underneath
provided for this, with the clamp facing
inwards to enable its subsequent insertion
in the kitchen unit.
Insert and simultaneously press the ends
so that the cooking hob is supported
uniformly on its perimeter.
Turn and screw the clamps for correct
mounting.
4 - The end of the inlet collector of the
gas hob has an elbow with
1
This elbow allows for:
A rigid connection.
and the oven, turn the elbow so as not to
create pressure in the pipe, bearing in
mind the position of the elbow according
to Figure 1. Make sure that after having
turned the elbow there is no leak.
In order to use this appliance in France
you need to remove the factory-assembled
adaptor and place the one found in the
accessory bag, Fig. 5b, without forgetting
to include the seal.
Except in the conditions outlined, it is not
possible to move or turn the elbow from
the position it is in when it leaves the
factory. If for any reason the elbow is
turned, you must ensure that the area is
sealed correctly.
Make sure that all connections made
are airtight.
The manufacturer is exempt from all
responsibility with regard to leaks, if
the elbow is moved or turned, as well
as connections made by the installation
technician.
5 - The following should be checked in
the specifications plate: the voltage and
the total power. This appliance must be
EARTHED.
Always make certain that all
national legal requirements. Observe all
the local electricity supply company
regulations.
To comply with normal safety
requirements, the installation technician
should provide an omni-pole cut-off switch
with a contact opening of at least 3 mm.
This appliance is type "Y", which means
that the supply cable MUST NOT BE
REPLACED BY THE USER; this can only
be done by the manufacturer's technical
services department.
Do not make any adjustments to the interior
of the appliance. If this is necessary, call
our technical assistance service.
1 - Minimum Distances (mm). Make
the
appliances regulation EN 30-1 ) is
Type 3.
-1
2 - When the wood fibres used for the
It is recommended that you call our
into the kitchen unit.
level of the hob must be 130 mm.
gas supply companies' specifications.
distance of this separator to the support
Place the cooking hob in the gap cut
All installation, regulation and adaptation
respecting all applicable regulations,
by an authorised installation technician,
Technical Assistance Service for
and gas supply.
to other types of gas must be carried out
standards and the country's electrical and
adaptation to other types of gas. Before
thread
(20,955 mm)
Figure 5a..
(L min. 1m - max. 3m).
With this option, you
must prevent the pipe
from coming into
contact with moving parts
of the insertion
unit (for example, a drawer)
or access to
any spaces which might
become
obstructed If the cooking hob is
joined
to an oven, as in Figure 6, or if there
is
obstruction between the flexible pipe
the installation, first check that it has been
an
on
supplied. Our cooking hobs leave the
l
a
hob as well as the dimensions of the gap
Check the dimensions of the cooking
All appliances containing any electrical
connections made are in accordance with
Connection using a flexible metal pipe
immediate vicinity of the cooking hob, must
Both the stratified surfacing and the glue
that is indicated on the specifications plate.
The place where the appliance is to be
This appliance
c
installed must have regulation ventilation
is the case, do not under any
adjusted for the type of gas that is to be
factory set to function with the type of gas
well venti
combustion
connected to a
2
/ "
so that flue gases are piped outside.
dis
p
product
's
o
y be installed in
sal
dev
existing regulations and venti
lat
ion
i
lated
place in accordance with
ce
specifications.The appliance
must
not be
.
Depending on the model, the clips and
Before connecting up the appliance to
production of the cooking hob modules
edges are treated with a special glue to
condensation that might drip down beneath
We therefore recommend that the cut
designed.
you begin, turn off the appliance's electricity
is used for the purpose for which it was
warranty will only be valid if the appliance
installed on on yachts or in caravans. The
the work surface of the cooker unit.
professional use. This appliance cannot be
home use only, not for commercial or
protect them from steam or any
This appliance has been designed for
We
a
r
p
r
o
t
e
c
t
i
v
e
g
l
o
v
e
s
t
o
f
i
t
t
h
e
h
o
b
.
Note
:
Loading ...
Loading ...
Loading ...