Loading ...
Loading ...
Loading ...
17
Amplifier detects audio on the Signal Sense input, the unit will automatically
power on. To disable this function, select the “Disabled” option which is the
factory default setting.
Options include: Disabled (Default), COAX , OPT , BLUETOOTH.
NOTE: When the amplifier enters standby mode via the remote control,
the Signal Sense function will not operate until the unit detects the audio
has stopped for the minimum 10 minute time-out period. This prevents
the unit from immediately powering back on if there is still active audio
playing.
NOTE: When the Signal Sense function is activated, the Amplifier will
consume additional power in signal sense standby mode.
NOTE: Due to local power consumption regulations the Signal Sense
function is not available in all markets.
Press the SETUP
B
button on the remote control to exit the setup menu or
select “Back” on the OSD to return to the main menu.
Display Configuration
Medium High
Medium
Low
Medium Low
DISPLAY
SETUP
Function
Brightness
High
Temporary Display
LED Brightness
Back
This Display menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
T
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
T
/
D
arrow buttons and
press the Enter
K
button to confirm.
Brightness: This function sets the brightness of the front display. The setting
is activated during normal operation by a PUSH RELEASE of the DISPLAY button
G
on the remote control. The OSD will always activate at the most bright level
regardless of the Brightness setting to ensure the unit configuration options
can easily be accessed and modified.
Options include: High (Default), Medium High, Medium, Medium Low, Low.
NOTE To dim the front display PUSH-HOLD the DISPLAY
G
button on
the remote control or 3 seconds.
Function: The amplifier can be configured to display the input audio source
as either a dB Peak Power Meter or a Frequency Spectrum Analyzer. The
display can also be configured as Status during normal operation. Select the
desired setting using the
T
/
D
arrow bPuttons and press the Enter
K
button to confirm.
Options includes: VU Meter, VU Meter x 2, VU Meter x 4, VU Meter x 8, Spectrum
8, Spectrum 12, Spectrum 16, Status (Default).
Temporary Display: This function allows the front display to temporarily show
changes to the amplifier for the time-out period before the display turns off
again. An example would be to turn on the display to show changes to the
source or volume levels then turn off the display after the time-out period
expires. To disable the temporary display and have the Amplifier display always
on set this function to Disable.
Options include: Disabled (Default), 5 seconds, 10 seconds, 15 seconds.
LED Brightness: Sets the brightness of the ON level of the front panel Power LED.
Options include: High (Default), Medium High, Medium, Medium Low, Low.
Press the SETUP
B
button on the remote control to exit the setup menu or
select “Back” on the OSD to return to the main menu.
System Configuration
Disabled
1 Hour
2 Hours
SYSTEM
SETUP
Software Version
Software Update
Factory Dafault
Auto Power Off
20 Mins
Back 5 Hours
PC-USB Version
12 Hours
This System menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
T
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
T
/
D
arrow buttons and
press the Enter
K
button to confirm.
PC-USB Version: This shows current loaded software version for PC-USB
processor.
Software Version: This shows the current software version loaded into the unit.
Auto Power Off: Set the amount of time the units stays powered on when
there is no audio signal. The amplifier will automatically go to standby mode
if audio is not detected for the specified timer period. Default: 20 Mins.
Options include: Disabled, 20 Mins, 1 Hour, 2 Hours, 5 Hours, 12 Hours.
Software Update: Select the desired update method to update the unit.
Options include: No (Default), USB, Internet.
Factory Default: This option sets the unit back to the original setting as when
it left the factory. All user settings will be erased.
NOTE Use caution when resetting the Amplifier to factory defaults as
all user configured options will be erased and reset to original factory
settings.
Press the SETUP
B
button on the remote control to exit the setup menu or
select “Back” on the OSD to return to the main menu.
Loading ...
Loading ...