Loading ...
Loading ...
Loading ...
5
Front Panel
Power Switch
The power switch turns the amplifier on and off.
When the Sonance logo on the power switch is lit solid white, the
amplifier has power and is turned ON and ready to operate.
When the Sonance logo is slightly dimmed the amplifier is in
standby mode.
When the Sonance logo on the power switch is blinking white, the
amplifier power supply is in thermal protection. The channel LEDs
will also light red when the power supply is in thermal protect mode.
NOTE: Upon initial power up there will be an approximately 12
second boot up cycle. This is normal.
Input/Output Lights
When each channel is active, the LED will light green as long as a
signal is present.
When the LED blinks red, this is an indication that the channel is
being overdriven.
When the LED lights are solid red this is an indication the amplifier
is in protect mode. While in protect mode the LED lights will
periodically light green to retest the output to determine if the short
has been removed. Protect mode could be caused by a short in the
wire, overheating of the amplifier or possibly an internal problem
with the amplifier.
NOTE: WHEN ANY OF THE LEDS ARE LIT RED TURN THE
AMPLIFIER OFF IMMEDIATELY. DETERMINE THE CAUSE OF THE
PROBLEM BEFORE TURNING THE AMPLIFIER ON.
Rear Panel
Power Cord
The Sonamp amplifiers feature removable IEC power connectors.
Plug the female end of the power cord into the Power Cord
Connector on the amplifier rear panel and plug the male end into a
grounded wall socket.
DO NOT plug the amplifier’s power cord into a convenience outlet
on any other audio or video component. If you need to use an
extension cord, use only a heavy duty (14-GAUGE OR LARGER)
extension cord to avoid starving the amplifier of the current
necessary for full operation.
AC Fuse Holder
To replace the fuse, unplug the power cord from the Power Cord
Connector and use a screwdriver to remove the fuse holder.
2-100 - 5 amp AC (T5-AL)
12-50 - 10 amp AC (T10-AL)
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE,
REPLACE THE FUSE WITH ONLY THE SAME TYPE AND RATING.
Auto On - Voltage In/Out
The Sonamp amplifiers can be turned on and off using 3-30 volts AC
or DC. The Voltage Output supplies a 12 volt DC signal to control
additional amplifiers or other equipment.
Volume Level Controls
Each channel on the amplifier has a volume adjustment pot
accessible on the rear panel of the amplifier.
Speaker Connections
The removable block connectors used on the Sonamp amplifiers will
accept up to 12 gauge wire.
Follow the connection layout on the rear panel of the amplifier.
Make sure no bare wires come in contact with the amplifier chassis.
When bridging channels, use the two outside connections on each
connector. The positive wire from the speaker should be on the
left side connection and the negative connection should be on the
right side.
Line Inputs/Loop Outputs
The 2-100 amplifier has LINE INPUTS and loop OUTPUTS.
The 12-50 amplifier has BUSS INPUTS A/B and loop OUTPUTS.
The loop outputs are non buffered, the maximum number of
amplifiers that can be looped together will depend on the output
capability of your source component.
SONAMP 2-100 & 12-50 MULTI-CHANNEL POWER AMPLIFIER INSTRUCTION MANUAL
FIGURE 5: SONAMP 2-100 MULTI-CHANNEL AMPLIFIER FIGURE 6: SONAMP 12-50 MULTI-CHANNEL AMPLIFIER
1L 1R
2-100
1L 1R
12-50
2L 2R
3L 3R
4L 4R
5L 5R
6L 6R
LEVEL LEVEL
BRIDGE
OFF ON
MONOSTEREO
12-50
S/N
VOLTAGE TRIGGER
IN OUT
AUTO ON
OFF
IN
OUT
IN
OUT
1-LEFT 1-RIGHT
LEVEL LEVEL
BRIDGE
OFF ON
MONOSTEREO
LEVEL LEVEL
BRIDGE
OFF ON
MONOSTEREO
LEVEL LEVEL
BRIDGE
OFF ON
MONOSTEREO
LEVEL LEVEL
BRIDGE
OFF ON
MONOSTEREO
LEVEL LEVEL
BRIDGE
OFF ON
MONOSTEREO
2-LEFT 2-RIGHT 3-LEFT 3-RIGHT 4-LEFT 4-RIGHT 5-LEFT 5-RIGHT 6-LEFT 6-RIGHT
LOCAL
BUSS A
BUSS B
LOCAL
BUSS A
BUSS B
LOCAL
BUSS A
BUSS B
LOCAL
BUSS A
BUSS B
LOCAL
BUSS A
BUSS B
LOCAL
BUSS A
BUSS B
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
LEFT RIGHT LEFT RIGHT
BUSS INPUT A BUSS INPUT B
1 - LEFT
1 - RIGHT
BRIDGE
8 Ω MIN
CLASS 2 WIRING
T10AL / 250VAC
CAUTION
R
EPLACE FUSE ONLY WITH
SAME TYPE AND RATING
ATTENTION
REMPLACER UNIQUEMENT AVEC LE
M
EME TYPE ET CALIBRE DU FUSIBLE
2 - LEFT
2 - RIGHT
BRIDGE
CLASS 2 WIRING
3 - LEFT
3 - RIGHT
BRIDGE
CLASS 2 WIRING
5 - LEFT
5 - RIGHT
BRIDGE
CLASS 2 WIRING
6 - LEFT
6 - RIGHT
BRIDGE
CLASS 2 WIRING
4 - LEFT
4 - RIGHT
BRIDGE
CLASS 2 WIRING
VOLTAGE
AUDIO
3-30 VOLTS
AC or DC
8 Ω MIN 8 Ω MIN 8 Ω MIN 8 Ω MIN 8 Ω MIN
156 watts
AC 100-120V ~ 60Hz
AC 220-240V ~ 50Hz
IN
OUT
1-L 1-R
LEVEL LEVEL
BRIDGE
OFF ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
S/N
T5AL / 250VAC
2-100
AC 100-120V ~ 60Hz
CAUTION
R
EPLACE FUSE ONLY WITH
SAME TYPE AND RATING
ATTENTION
REMPLACER UNIQUEMENT AVEC LE
M
EME TYPE ET CALIBRE DU FUSIBLE
VOLTAGE TRIGGER
IN OUT
AUTO ON
OFF
1 - LEFT
1 - RIGHT
BRIDGE
CLASS 2 WIRING
VOLTAGE
AUDIO
3-30 VOLTS
AC or DC
8 Ω MIN
AC 220-240V ~ 50Hz
52 watts
Loading ...
Loading ...
Loading ...