Loading ...
Loading ...
Loading ...
en Operating the appliance
8
Automatic mode
Switching on
■ Touch the # symbol.
The fan will start at setting 2.
■ Touch the ! symbol.
The optimum fan setting is set automatically using
an air quality sensor.
Switching off
Touch the ! or # symbol to switch off automatic
mode.
The fan will switch itself off automatically if the air quality
sensor detects no further change in the air quality in the
room.
Automatic mode can run for a maximum of four hours.
Sensor control
In automatic mode, an air quality sensor in the extractor
hood detects the intensity of the cooking and roasting
odours. Depending on the air quality sensor setting, the
fan will switch itself to another fan setting automatically.
Possible sensor settings:
Default sensitivity setting:
„
Lowest sensitivity setting: ‚
Highest sensitivity setting: †
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1. Touch and hold the ! symbol for one second
when the fan is switched off. The setting will be
displayed.
2. Slide your finger across control panel III to change
the sensor control setting.
3. Take your finger off the ! symbol.
Fan run-on time
Switching on
Note: If intensive mode has been activated, the run-on
function will not be available.
Touch the A symbol until x lights up on the display
panel.
The fan will run at fan setting 1.
After approximately 10 minutes, the fan will switch itself
off automatically.
Switching off
Slide your finger to the right across control panel III until
a fan setting lights up in the display.
This immediately stops fan run-on.
Saturation display
If the metal grease filters or the activated charcoal filter
are/is saturated, the corresponding symbols flashes
after the appliance is switched off:
■ Metal grease filters: !
■ Activated charcoal filter: "
■ Metal grease filters and activated charcoal filter: !
and "
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 12
Note: The saturation indicator does not apply for non-
renewable activated charcoal filters that are inserted
downstream of the metal grease filter. These activated
charcoal filters must be replaced twice a year.
The saturation indicators can be reset while they are
flashing. Slide your finger to the left across the control
panel to do so.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■ The extractor hood must be connected and switched
off.
■ Touch and hold the # and ! symbols at the
same time until "2" lights up for air recirculation
mode (filters that cannot be regenerated).
■ Repeatedly touching and holding this button
combination makes "3" light up for air recirculation
mode (filters that can be regenerated).
■ Repeatedly pressing and holding this button
combination switches the electronic controller back
over to air extraction mode ("1" ).
Audible signal
Switching on
Touch and hold the
# and & symbols at the same time
for approximately 3 seconds when the fan is switched
off. An audible signal will sound as an
acknowledgement.
When the signal tone is activated, ‚ will be lit.
Switching off
Touch and hold the
# and & symbols at the same time
for approximately 3 seconds when the fan is switched
off. An audible signal will sound as an
acknowledgement.
When the signal tone is deactivated, ‹ will be lit.
Connecting to a hob en
9
eConnecting to a hob
Connec t i ng to a hob
You can connect this appliance to a hob (if the hob
supports connection to the appliance) and then control
the functions of the hood via your hob.
Appliances can be connected to each other in different
ways:
Home Connect
Two appliances can be connected using the Home
Connect app provided that both of them are Home
Connect compatible.
Refer to the Home Connect documents supplied for
more information.
Connecting appliances directly
If the appliance is connected directly to a hob, it cannot
be connected to your home network as well. The
appliance will function as an extractor hood that is not
connected to the network and you can continue to
operate it via the control panel.
Connecting appliances via your home network
If the appliances are connected to each other via your
home network, both the hood controls on the hob and
Home Connect can be used to operate the appliance.
Notes
■ Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the hob.
■ If the extractor hood is being operated by means of
the controls on the hood itself, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
Setting up a connection
The hood must be switched off before you can connect
the hob and extractor hood.
Connecting directly
Make sure that the hob is switched on and is in search
mode.
To do this, refer to the section entitled "Connecting to
the extractor hood" in the instruction manual for your
hob.
Notes
■ Before connecting the appliance, reset all existing
connections to the WiFi or other appliances.
■ If your extractor hood is connected directly to the
hob, it cannot be connected to your WiFi as well and
you will not be able to use Home Connect.
Press and hold the
& symbol until the D and Ù
indicators start flashing.
The extractor hood has been connected to the hob
when the D symbol stops flashing and remains
continuously lit.
Connecting via your home network
Follow the instructions in the section entitled "Automatic
login to your home network" or "Manually logging into
your home network" ~ "Home Connect" on page 10
Once the extractor hood is connected to your home
network, you can connect to the hob via the Home
Connect app. To do this. follow the instructions on your
mobile device.
Loading ...
Loading ...
Loading ...