Candy CDF 625 A-S Dishwashers

Installation, Use, Maintenance - Page 88

For CDF 625 A-S.

PDF File Manual, 104 pages, Read Online | Download pdf file

CDF 625 A-S photo
Loading ...
Loading ...
Loading ...
Loading the salt
On the bottom of the machine there is a
container for the salt for regenerating
the softener.
It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance.
To add salt, unscrew the cap of the con-
tainer on the bottom and then refill the
container.
During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
After loading the salt, it is recommended
running a complete washing cycle,
or COLD RINSE programme. The salt
dispenser has a capacity of between 1.5
and 1.8 kg and, for efficient use of the
appliance, it should be refilled from time
to time according to the regulation of the
water softener unit.
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.
89
Salt loading indicator
Some models are provided with an indicator
light which signals salt consumption.
The signal will appear according to one of
two systems:
an indicator light on the control panel
which will light up when it is necessary to
reload the salt container;
the salt container cap with a green
mobile light (fig. 1a) which remains
visible as long as there is enough salt for
regeneration purposes. When the green
surface is depressed inside the cap,
more salt must be loaded.
Other models are provided with a blind cap
(fig. 1b). In this case, the salt level must be
checked periodically, according to the
regulation of the water softener unit.
IMPORTANT
The appearance of white stains on
dishes is generally an important
sign that the salt container needs
filling.
Fig. 1
a b
If your water is at level 0, you need not use
any regenerating salt, nor need you make
any adjustment, as your water is soft.
According to the degree of hardness of
your water, regulate the softener unit in the
following way:
1. remove the lower rack. Unscrew and
remove the cap from the salt dispenser
located in the bottom of the tub
(fig. A"1");
2. turn the selector screw to the required
position with a screwdriver or a knife.
N.B.: For models fitted with electronic
programmer refer to the programme
list enclosed.
88
TYPE 1
TYPE 2
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes.
The softener unit can treat water with a
hardness of up to 60°fH (French grading)
or 33°dH (German grading) through five
different settings.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
The table below lists different degrees of
water hardness with the corresponding set-
ting for the softener unit.
*The water softener unit is set in the
factory at level 2, as this is suitable for the
majority of users.
Level
0
1
*2
3
4
Water
hardness
°fH
(French)
0-9
10-30
31-40
41-50
51-60
Water
hardness
°dH
(German)
0-5
6-16
17-22
23-27
28-33
Use of
regenerating
salt
NO
YES
YES
YES
YES
Water
softener
setting
FREE
position
N.1
position
N.2
position
N.3
position
N.4
of
washes
50
40
30
20
Loading ...
Loading ...
Loading ...