Loading ...
Resetting your lter indicator
Note: These are the most common lter reset instructions. If the instructions
don’t work for your refrigerator brand, see the documentation that came with
your refrigerator.
Troubleshooting
Storage and maintenance
• Replace your lter every three to six months to prevent bacteria and
fungus growth in your lter, supply lines, and storage tank.
• Stored lters do not expire. Keep your unused lters in a cool, dark, and
dry place until you need them.
• If you do not use your water dispenser for more than four days, run two
gallons of water before using it to prevent bad tasting water.
• The lters are lubricated with a safe, USDA grade silicone. You do not need
to lubricate the gaskets or receiver before installing.
V2 ENGLISH 14-0651
Recycling your used Insignia lter
Help the environment by recycling your used Insignia lter at your local
recycling facility or mail it to:
Insignia Filters
2678 Ram Bay Road
Manning, South Carolina 29102
6-month limited warranty
For complete warranty, visit www.insigniaproducts.com.
Contact Insignia
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
CERTIFICATIONS: <SGF-G9, SGF-LB60, SGF-DA20B, SGF-DSB30>
INSIGNIA is a registered trademark of BBY Solutions, Inc. Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 BBY Solutions, Inc. All Rights Reserved.
REFRIGERATOR
BRAND
Amana
GE or Hotpoint
Samsung
LG
Kenmore
INSTRUCTIONS
Press and hold the dispenser lock and auto light buttons at the
same time. When the lter indicator ashes (about four seconds),
release both buttons.
OR
Press and hold the dispenser lock and water buttons at the same
time. When the lter indicator ashes (about four seconds), release
both buttons.
Press and hold the reset water lter button on the dispenser for
three seconds.
Press and hold the ice type and child lock buttons for three
seconds. The water lter indicator should turn green.
Note: Only hold these buttons for three seconds. Holding these
buttons for ve seconds cancels the reset. If you cancel the reset,
repeat the instructions above again.
Press and hold the reset button for three seconds.
The water lter reset for Kenmore refrigerators varies by model.
See the documentation that came with your refrigerator.
PROBLEM
My refrigerator is
not dispensing
water
My water
dispenser is
dripping
My water is cloudy
or contains black
carbon pieces
My new lter is
making noises or
sputtering
My water tastes
bad
SOLUTION
• Make sure that you soaked your lter in water for 15 minutes before
installing.
• Make sure that the lter is securely connected to the receiver. Do not
use tools to tighten the lter in place.
• Make sure that the water line to the refrigerator is turned on. The
valve must be completely open for the refrigerator to receive water.
• Make sure that the refrigerator door is closed or the dispenser will not
work.
• A few drops are normal. If the water is dripping constantly, have a
service technician check your refrigerator’s water valve.
• Cloudy water is caused by microscopic air bubbles. Run two to three
gallons of water from your dispenser to clear the air bubbles out.
• Black carbon pieces in the water are normal and appear with all
carbon lters. Run two to three gallons of water through your
dispenser to remove loose carbon pieces.
• Make sure that you soaked your lter in water for 15 minutes before
installing.
• Noises and sputtering are caused by trapped air pockets. Run two to
three gallons of water from your dispenser to push the air out.
• If you do not use your water dispenser for more than four days, run
two gallons of water through the dispenser before using it.
• Make sure that you replace your lter every three to six months to
prevent bacteria growth.
C
M
Y
CM
MY
CY
CMY
K
NS-MWF-2_NS-LT600B-2_NS-DA2920_NS-DA2920-2_NS-DA2903_NS-DA2903-2_14-0651_QSG_V2_EN.ai 2 6/19/2014 11:31:05 AMNS-MWF-2_NS-LT600B-2_NS-DA2920_NS-DA2920-2_NS-DA2903_NS-DA2903-2_14-0651_QSG_V2_EN.ai 2 6/19/2014 11:31:05 AM