Loading ...
Loading ...
Loading ...
5
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED
TIME TO
CYCLE
ADDED
WATER
GALLONS
(LITERS)
Activates the TargetClean™ spray jets and provides intensified water
spray to back of lower level rack.
May add heat and time to cycle.
Sensor
Heavy
Normal
Soak & Clean
Raises main wash
temperature from
105°F (41°C)
to120°F (49°C).
0:12 to 0:57 0 to 4.8
(0 to 18.2)
Raises main wash temperature to improve cleaning for loads
containing tough, baked-on food.
Sensor
Heavy
Normal
Soak & Clean
Raises the main
wash temperature
to 135°F (57°C).
0:05 to 0:13 0 to 3.86
(0 to 14.6)
Sanitizes dishes and glassware in accordance with NSF International
NSF/ANSI Standard 184 for Residential Dishwashers. Certified
residential dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have been designed to meet
the requirements of the NSF/ANSI 184 performance standard for soil
removal and sanitization efficacy. There is no intention, either directly
or indirectly, that all cycles on a NSF/ANSI 184 certified dishwasher
meet the NSF/ANSI 184 performance standard for soil removal and
sanitization efficacy.
Sani Rinse indicator is lit at the end of the cycle if the Sani Rinse
option was successfully completed. If indicator does not light, it is
probably due to the cycle being interrupted.
Sensor
Heavy
Normal
Raises the main
wash temperature
to 135°F (57°C)
and the final rinse
temperature to
156°F (69°C).
0:05 to 1:06 0 to 3.86
(0 to 14.6)
Dries dishes with heat. This option, with the use of rinse aid, will
provide the best drying performance. Plastic items are less likely to
deform when loaded in the top rack. Use Heat Dry for optimum dry
performance, Turn the Heat Dry option off for air dry.
Sensor
Heavy
Normal
Soak & Clean
Uses heating
element to speed
drying times. Heat
Dry option defaults
to On when any
cycle is selected,
except for 1- Hour
Wash.
0:08 to 0:46 0
Runs dishwasher at a later time. Select a wash cycle and options.
Each time you press the delay button it will display the next available
delay time. Press DELAY. Press START/RESUME. Close door firmly.
NOTE:
The dishwasher remembers the last Delay you selected. To
reset the delay time to something other than what is displayed,
continue to press the Delay button until the desired delay time is
reached.
NOTE:
Anytime the door is opened (such as, to add a dish); Start/
Resume must be pressed again to resume delay countdown.
Available with
any cycle
Delays start of a
cycle up to
24 hours
.
0:00 0
Avoids unintended use of dishwasher between cycles or cycle and option changes during a cycle.
To turn on Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Control Lock light will stay
on for a short time, indicating that it is activated and all buttons are disabled. If you press any button while your dishwasher is locked, light
flashes 3 times. Dishwasher door can still be opened/closed while the controls are locked.
To turn off Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Light turns off.
NOTE:
If your model requires you to press and hold DELAY to lock controls, Control Locked LED will be on or off to indicate whether
Control Lock is active or not.
Control Purpose Comments
Press to start or
resume a wash
cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED
flashes. Cycle will not resume until door is closed and Start/Resume is pressed.
NOTE: If Start/Resume button is located on top of door, push door firmly closed within 3 seconds
of pressing Start/Resume. If door is not closed within 3 seconds, Start/Resume button LED will
flash, an audible tone will be heard (on some top control models), and cycle will not start.
Press to cancel
wash cycle.
If Start/Resume button is located on top of door, press and hold START/RESUME for 3 seconds.
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let dishwasher
drain completely.
To follow progress
of your dishwasher
cycle.
NOTE:
Indicators
shown are not
available on
all models.
The Clean indicator glows when a cycle is finished.
If you select Sani Rinse option, when cycle is finished, the “Sanitized” indicator glows. If your
dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can
happen if the cycle is interrupted, or water could not be heated to required temperature.
The light goes off when you open and close door or press CANCEL.
Loading ...
Loading ...
Loading ...