Kesnos PD160A 34 Pints Compact Home Dehumidifier for Space up to 2,500 Sq. Ft

Parts description

Front

Rear

Control Interface

Control Panel

Power Button: Press one time is turn on. press again is shutdown.the figures and lights will quench when machine shutdown.

Humidity Button: Each click, 5RH% increase by degrees. can be set range: 30 RH% ~ 80 RH%. can berecycled set; Press 2 seconds, can adjust settings value continuous.

Timer Button: Each click, 1h increase by degrees. can be set range: 1-24h, can be recycled set; Press 2 seconds, and can adjust settings value

Speed Button: Set the high, low wind speed.

Lock Button: Press the button and hold for 2 seconds and the control panel will be locked.

Operation Instruction

Setting

Humidity Setting

In the power on stating, press the "set key" can set the humidity value, each click, 5RH% increase by degrees. range of 30 RH% ~~ 80RH% an be cycle setting, press two seconds. can adjust setting value continuous. automatically exit once stop press button few seconds. When sett- ing 30 RH%, is continuous dehumidification state. humidity digital flashes when setting.

Timing Setting

In the Power off state, is timer-power-on. in the power on state. is timing power off.

Press the "timing" key, can set timing time. setting range: 1-24h. an be recyclable setting. et "00" to be invalid. Press 2 seconds. can adjust settings value continuous;

When timing setting, timing lights flashing The timing lights bright and nixie tube display humidity when the timing effective; effective digital display humidity. but press "timing" button one time. an be display the timing time. after 5 seconds then automatically return back display humidity. back to the current humidity value.

The Wind Speed Setting

In the power on state. press the "SPEED" key. can select "high wind" or" low wind", efault "high wind"speed. In Corresponding state, "high wind" or "low wind" lights, constant bright.

Lock setting

When the unit is turned on. press "LOCK" and hold on for 2 seconds, the control panel will be locked together with the other buttons. To unlock the control panel. press and hold the "LOCK" button again for 2 seconds.

Water Overfill Protection

When the bucket full of water. the machine will turn off automatically. The indicator light will flash. After you empty the water from the bucket the indicator light will off. The machine will restart to work. (machine start and stop interval 3 minutes delay).

Defrost Function

When running under lower ambient temperature. the system will automatically determine if there is frost. if have. frost will automatically defrost.

• Defrost action: fan (high wind speed) work, compressor stop.
• The defrost display: during defrosting, defrost" indicator flashes, otherwise off.

Action Description

• Power on: compressor start after fan work a few seconds.
• The shutdown: compressor stop. after a few seconds fan stop. anion stop, (Other failure or humidity reached the required. if need shutdown. ans stop need dozens of seconds). Have 3 minutes delay protection function. means in the power on state, shutdown three minutes then to start again.

Display Status Descripion

• Delay power on state. "" light flashes; "" lights lit when the machine is running,
• When machine stop as the current humidity reaches the set humidity, it's wet-controlled state, "humidity" and "running" light are flashing
• Press "Lighting" key, hen turn on this button, the control panel light will on, use the light up function the light will on, therwise off;
• Press the "SPEED" key, high wind lamp High light when is "high wind speed", low wind lamp low light When " low wind speed" ;
• Timing lamp lights Timing effective, otherwise off;
• Defrost lights flashing when in the defrost state, otherwise off;
• Water full lamp flashing when in the water full state, otherwise off.

Error & Protection Code

1. Code E1 Humidity sensor error.
2. Code E2 Defrost temperature sensor error.
3. Code E4 Temperature sensor error.
4. Code E7 Water tank is full.

Attention

When the machine signals the alarm, it will flash or display the alarm. in case there are multiple error on the unit. it will show the error in a turn display behavior.

1. If the display reads “E1”,“E2” or “E4” error codes, please turn off and unplug the unit, and check for any obstructions. Plug it in again and restart the dehumidifier.
2. When one of the above malfunctions occurs, the buzzer will alarm for a few seconds. Press any key during the alarm to release the alarm sound.

If the malfunction is still present, please don’t hesitate to contact Kesnos. Customer Service email: [email protected] for help.

Note: Before starting the machine, please ensure that the air outlet has been opened, otherwise the machine will overheat. Do not pull out the power cord directly to stop the machine.

Empty the Tank or Bucket

There are two ways to remove collected water.

Use the Bucket

When the water tank is already full, the Full Tank Alert indicator will light up, the dehumidifier will automatically shut down until the tank has been emptied and placed back to the unit.

Empty the Water Tank

Continuous Drainage

When you are not using water tank drainage, ou can select a continuous drainage.

1. When select the water tank drainage, please insert the "Plug" on the continous drain port to prevent water leakage.
2. When select continuously drainage, please insert the "Plug" on the water tank drain port to prevent water leakage.

NOTE

• Make sure the connection is tight and there is no leaking.
• Lead the water hose to the floor drain or a suitable drainage facility, he drainage facility should be lower than the drain outlet of the dehumidifier.
• Be sure to run the water hose sloping downward to let the water flow out smoothly.
• When the continuous drain feature is not being used. remove the drain hose from the outlet.

Cleaning And Maintenance

WARNING

In order to avoid electric shocks. please power off the machine and pull out the plug before cleaning or repair.

A-Cleaning the dehumidifier body

Please use only a soft and a bit wet textile or cloth to clean it.

B- Cleaning filter

• Pull out the filter.
• Clean the filter: Use a vacuum cleaner to gently remove the dust from the surface of the filter. If the filter is very dirty, wipe it with warm water anda mild detergent and dry it completely.

Slowly insert the filter back into the fuselage.

C-Dehumidifier storage

When you want to store the dehumidifier because you don't use it for along time. Please pay attention to the following steps:

1. Empty the water in the water tank.
2. Roll up the power cord and tie it up.
3. Clean the filter.
4. Place the machine in a cool and dry environment.

Troubleshooting

Check the information below for troubles hooting steps that will save you time to resolve issues that may happen with the unit. The list includes most common issues. Listed below are not result of defective unit, crafts or materials in the unit. If all troubleshooting steps has been exhausted and issue is still occurring, feel free to get in touch with Kesnos Customer.

Service to get further assistance.

Problem, Cause & Solution

1. Dehumidifier does not work

• The power cord is unplugged
  • Make sure that the unit's plug is inserted properly into the power outlet.
• Is the TankFull indicator blinking? (The tank is full or in awrong position)
  • Empty the water in the water tank and then reposition the tank.
• Is the room temperature above 95°F (35°C) or below 41°F (5°C)
  • This product does not apply to over hot or cold environment, the machine will automatically protection it is anormal phenomenon.
• Is the room temperature between 41°F (5°C) and 68°F (20°C)?
  • When running under lower ambient temperature, the machine will automatically defrost, it is a normal phenomenon. Wait until the defrost process finish, it will restart dehumidifying again.
• The dehumidifier is in the defrosting process
  • It is normal the compressor ceases while defrosting process. Wait until the defrost process finish, it will restart dehumidifying again.
• Does the room humidity is lower than or reach the preset humidity level? (The room humidity has reached the preset humidity level, the dehumidifier enters into Standby Mode and the the LCD and indicators will flashing.)
  • Please set the humidity 5% decrease by degrees than the room humidity or set the humidity to 30%
• There is prevent frequent start function in the machine. Dose the machine stop working just now?
  • Please wait for more than 3 minutes.
• Room humidity is low.
  • The dehumidifier is designed to work in the humidity range of 30%-80%. Above or below the work humidity range, it will not work.

2. Dehumidifier does not dry the air as it should

• The air filter is dirty.
  • Clean the air filter.
• Is the air inlet or air outlet obstructed?
  • Remove the obstruction from the air inlet or outlet.
• The dehumidifier size is too small for application.
  • Increase the quantity of dehumidifier. Or change a higher capacity dehumidifier.
• Poor air circulation.
  • Please leave about 7.9inch (20cm) around the product.
• Did not allow enough time to remove the moisture.
  • Allow enough time to remove the moisture.
  • When first installed, allow at least 3-4 days to maintain the desired RH.
• The room has not been sealed properly.
  • Check that all doors, windows and other openings are securely closed.
• The air filter is clogged.
  • Wash the filter.
• Room temperature is too low, or below 41°F (5°C) (The machine will not work and or poor dehumidify efficiency in low temperature).
  • Please wait the temperature rises above 5°C or higher.

3. The dehumidifier makes loud hoise when operating

• The dehumidifier is not positioned level.
  • Move the machine to a horizontal position.
• Is there blocking around the air inlet? The air filter is clogged
  • Clean up the dirty form the on the air outlet and intake.
• Is the filter installed correctly?
  • Please check whether the filter packing bag removed and install correctly.

4. Dehumidifier operates lcontinuously

• Check if the dehumidifier is in CONTINUOUS MODE.
  • Don't set the humidity too low. Typically 40-50% are good settings to use.
• Room humidity is too high
  • Change humidity settings. Or change a higher capacity dehumidifier.
• Doors and windows are open
  • Ensure that all doors, windows and other openings are closed.

5. Overflow of water on floor

• Hose to connector or hose connection may be loose.
  • Connect the hose with the drain outlet tightly.
• The water bucket has not been installed properly.
  • Re-install the water bucket properly.
• The water tank's float has been stunk.
  • Move the float and let it can be swung freely.
• The magnet on the float comes off.
  • Put the magnet in right position.

Warning: If the dehumidifier is still not working properly as expected and the troubleshooting steps or solutions above may not resolve the issue.Piease unplug the power and shut down the dehumidifier then contact Kesnos customer service [email protected]

Safety Note

1. When using, please do not put the machine at the soft and movement

2. Do not insert thin rods and hard objects into the fuselage to avoid malfunction and danger.

3. When using. please keep the machine away from heating furnace. electric kettle and other heat sources.

4. When using make sure doors and windows are closed to get the best humidity removal effect.

5. Please do not put objects around the body. If the ventilation is t blocked. the dehumidification effect will be affected.

6. If do not use the product fora long time please unplug the power cord.

7. When cleaning the dehumidifier fuselage, please use wet cloth or textile to wipe the unit's surface gently, do not splash water on the unit directly.

8. Please do not put any object on the dehumidifier.

9. Please clean the filter every two weeks (do not use hot water above 104°F gasoline toluene)

10. When on continuous drainage. make sure the drainage pipe is placed horizontally on the ground.
Avoid the pipe to be on uneven surface or in an arch position.

11. After cleaning the filter, do not dry the unit under direct sunlight to avoid filter deformation.

12. Before moving and carrying the machine please first pour out the water in the tank

Specification

Related Products