Loading ...
Loading ...
Loading ...
Operating the control panel
• The light of the selected button MIN(DELICATES)/ NORMAL / MAX(JEANS) flashes while the appliance is warming up.
• When the red «Water tank empty» light is flashing the water tank is empty. Fill the water tank and press the «OK»
button for the light to switch off. See paragraph «Filling the water tank during use».
• When the orange «Anti-calc» light is flashing : maintenance is required, see paragraph «Maintenance and cleaning».
• Your steam generator comes with an automatic shut-off system which activates after approximately 8 minutes
without use. Only the blue light of the «ON-OFF» button is flashing: the steam generator is on standby. Press the «ON-
OFF» button or the steam shot button to start ironing again. See paragraph «AUTO-OFF» System.
Use
Steam ironing
• We recommend that you use a mesh type ironing board to allow steam to pass through
the garments for better ironing results and also to prevent steam venting sideways.
• To obtain steam, press the steam control button under the iron handle. The steam
will stop when you release the button.
• After approximately one minute, and regularly while it is being used, your steam
generator’s electric pump injects water into the boiler. It makes a noise but this is
quite normal.
• If you are using starch, always spray it onto the reverse side of the fabric to be ironed.
Smart Technology Auto control
Your steam generator is fitted with SMART TECHNOLOGY AUTO CONTROL electronic regulation which gives you a
choice of three optimum temperature and steam combinations.
Do not iron over zips, studs or
other hard or sharp objects which
may damage the soleplate. Do
not place the iron on a metal
support. When taking a break
from ironing, always place the
iron on the iron rest plate of the
unit. It is equipped with non-slip
pads and has been designed to
withstand high temperatures.
Dry ironing
• Do not press the steam control button under the iron handle.
Vertical steam ironing
• Hang the garment on a coat hanger and hold the fabric slightly taut with one hand.
• As steam is very hot: never attempt to remove creases from a garment while it is
being worn, always hang garments on a coat hanger.
• Holding the iron in a vertical position tilted slightly forwards, press repeatedly on the steam
control button (underneath the iron handle) moving the iron from top to bottom.
Power Zone Function
• Your appliance includes the Power Zone function: concentrated steam shot at the tip of the soleplate, to be used in
particular to target stubborn creases, detailing and zones that are difficult to access.
• To use this function, press the Power Zone button on top of the iron as often as necessary
Steam boost function
• Your appliance includes the Steam boost: automatic sequential steam for effortless use. To be used in particular for
thick fabrics.
• To obtain this function, press the steam control button under the handle three times in quick succession.
Refilling the tank during use
• When the red «Tank empty» light is flashing, there is no more steam. The water tank is empty.
1. Remove the detachable water tank using the handle (located at the front of the steam generator) and fill it without
exceeding the MAX level.
2. Push it back into its housing until you hear a «click».
3. Press the «OK» button located on the control panel until the light goes out to continue ironing.
Maintenance and cleaning
Cleaning your steam generator
Ultragliss soleplate (depending on model):
• While the soleplate is still warm, clean it with a damp non-metallic pad.
Your steam iron is fitted with a Gliss/Glide ProtectTM Autoclean soleplate (depending on model):
• Its exclusive active coating allows it to eliminate any impurities that may be regularly generated during normal
conditions of use.
• Ironing with an unsuitable program could nonetheless leave traces that require manual cleaning. In this case, we
recommend using a soft damp cloth on the soleplate while it is still warm to avoid damaging the coating.
Warning! Using an abrasive pad will damage the soleplate’s autoclean coating
• Do not use detergent or descaling products for cleaning the soleplate base-unit.
• Never hold the iron or the base unit under the tap.
• Regularly clean the soleplate with a damp, non-metallic washing up pad.
• Clean the plastic parts of the appliance occasionally with a soft cloth.
Easy descaling of your steam generator
To extend the life of your steam generator and avoid scale on your ironing, your steam
generator is equipped with a built-in scale collector. This collector, located in the boiler
tank, automatically removes the scale that forms inside.
Operation:
• An orange «anti-calc» light located on the control panel starts flashing to tell you that the anti-calc collector needs
rinsing.
Important: This operation must not be carried out unless the steam generator has been unplugged for at least two
hours and has cooled down completely. To carry out this operation, the steam generator must be close to a sink as water
may come out of the boiler tank when it is opened.
• Once the steam generator has completely cooled down, lift the tab.
• Fully unscrew the collector - and pull it out of the base unit - it contains the scale that has built up in the boiler tank.
• To clean the collector, simply rinse it under running water to remove any scale it contains .
• You can soak the collector rod in white vinegar (available from hardware stores) or lemon juice for a few hours to
remove any stubborn scale stuck to the rod.
• Start w ith the fabrics to be ironed at a low temperature and finish with those that need higher temperature.
• If you are in doubt about the type of fabric an item of clothing is made from, check the label.
• When you select a higher temperature, you can continue to iron provided that you are not ironing a more delicate
fabric that requires a lower temperature. If you select a button to reduce the temperature you should wait until the
blue iron light has stopped flashing before continuing to iron.
*If you are ironing woollen garments, press repeatedly on the steam shot button without placing the iron on the
garment. This will avoid it becoming shiny.
Warning, fabrics with the symbol are not suitable for ironing.
ECO MIN MODE: The ECOmin function reduces energy consumption. Press the ECO button to change to ECO mode and
press the same button again to exit this mode.
During use if you have not used the steam function for a few minutes, press the steam control button several times in a
row. Holding the iron away from your laundry. This will remove the cold water from the steam circuit.
Settings Recommended use Labelling Examples
NORMAL Best for all standard linen
Cotton, wool*, silk, polyester, cashmere, mohair,
viscose and synthetic/cotton mixes.
MAX
(Jeans)
The most effective for thick
or difficult to iron fabrics
Linen, thick cotton, jeans (dark colours)
MIN
(Delicates)
Very gentle, for the most
delicate items and sensitive
colours
Acetate, elastane, polyamide, acrylic and
synthetic mixes.
Note: do not use steam to iron acrylic
or modacrylic fabrics.
Loading ...
Loading ...
Loading ...