Loading ...
Loading ...
4 5
2. Parts and Controls
1. Massage surface with 18 (9 on each side) massage balls
2. Power Switch
3. Mode Button
Press once: Low-speed massage
Press twice: Higher speed massage with heat
Press three times: Off
4. Adjustable feet
3. To Set Up
1
. Remove massager from packaging and check all components for damage.
2
. Connect the power cord to a standard electrical outlet and route the power cord to prevent anyone from
tripping over it.
4. To Use
1
. Remove your shoes before each use. Sit comfortably and place your feet on the massage balls. The rub-
ber feet on the massager base should prevent it from moving.
2
. Press the Power Switch to the | (on) position and then press the Mode Button. To activate the heat func-
tion and the higher speed setting, press the Mode Button again. Press the Mode Button again to switch
the massage balls and heat function off.
3
. Press the Power Switch to the O (off) position to shut the massager off.
NOTES:
For an optimum massage position, the rear rubber feet can be adjusted. Turn clock-
wise to raise or counterclockwise to lower until you hear a click. Each rear rubber foot
has two height settings.
The massage should be pleasant and relaxing at all times. Stop the massage or change
your position or the contact pressure if it is painful or unpleasant.
Massaging a specific point on the sole of the foot may influence the corresponding
organ of the body. Study relevant literature and ask your doctor before using point
reflex zone massage to achieve the desired effect.
CAUTION
•
Do not force any part of your body, in particular your fingers, between the rotating massage balls
and their mounting points.
•
Do not use the massage device for longer than 15 minutes or it can overstimulate the muscles and
cause tension instead of relaxation.
1
2
4
3
5. Care and Maintenance
WARNING:
•
Disconnect the power cord from the electrical outlet before cleaning.
•
Only clean the appliance in the manner specified. Never allow liquids to enter the device or its
accessories.
•
Before cleaning the appliance, make sure that the appliance is switched off and the power supply
is disconnected. Allow the unit to cool down.
•
Clean the massager withe a slightly damp sponge only. Never use brushes, aggressive cleaning
agents, petrol, thinners or alcohol. Rub the unit dry with a clean dry cloth.
•
Never immerse the appliance in water to clean it and ensure water cannot get into the appliance.
•
Wait until the device is completely dry before using it again.
•
Undo any kinks in the cable.
•
Take care to roll up the mains lead to avoid damaging it.
•
You should ideally store the device in its original packaging and keep it in a clean, dry place.
If you do not use the device for longer periods, store it in the original packaging in a dry place. Do not place
any objects onto the packaging.
Problem Cause Remedy
Massage balls rotating at
reduced speed
The load on the massage balls is
too great.
Release the massage balls.
Massage balls not moving Appliance not connected to the
power supply.
Connect the mains plug and
switch on the device. Set the
main switch to 1.
6. Technical Data
Power: 120V~ 60Hz 48W
Size: ~ 14.8 in x 16.9 in x 4.33 in (37.5 x 43 x 11 cm)
Weight: ~ 6.8 lb (3.1 kg)
7. Warranty
Limited Lifetime Warranty For Original Purchaser
Your Beurer Foot Massager, Model FM 60, is warranted to be free from defects in materials and workmanship
for the life of the product under normal conditions of intended use and service. This warranty extends only
to the original retail purchaser and does not extend to retailers or subsequent owners.
We will, at our option, repair or replace the Beurer Foot Massager, Model FM 60, without additional charge, for
any part or parts covered by these written warranties. No refunds will be given. Repair or replacement is our
only responsibility and your only remedy under this written warranty. If replacement parts for defective mate-
rials are not available, Beurer reserves the right to make product substitutions in lieu of repair or replacement.
For warranty service contact our customer service department at 1-800-536-0366 or at info@beurer.com to
provide a description of the problem. If the problem is deemed to be within the scope of the limited lifetime
warranty, you will be asked to mail the product at your costs in its original package with proof of purchase,
your name, address and phone number. If the problem is not deemed to be within the scope of the limited
lifetime warranty, we will provide a quotation for repair, respectively, replacement and return shipping fee.
This warranty does not cover damage caused by misuse or abuse; accident; the attachment of unautho-
rized accessories; alteration to the product; improper installation; misapplication; lack of reasonable care
with respect to the product; unauthorized repairs or modifications; improper use of electrical/power supply;
normal wear; loss of power; dropped product; malfunction or damage of an operating part as a result of
failure to comply with instructions for use or to provide manufacturer’s recommended maint nance; transit
damage; theft; neglect; vandalism; or environmental conditions; loss of use during the period the product is
Loading ...
Loading ...
Loading ...