Loading ...
Loading ...
Loading ...
en Trouble shooting
20
3Trouble shooting
Tr oubl e s hoot i ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
■ If “ appears on the display, press and hold the
button for the relevant cooking zone in order to read
the fault code.
■ If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
■ If a fault occurs, the appliance will not switch to
standby mode.
Cleaning
How do I clean the hob?
Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-
water detergent (concentrated) or scouring pads.
You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning"
Display Possible cause Solution
None The power supply has been disconnected. Use other electrical devices to check whether a short-circuit has
occurred in the power supply.
The device has not been connected in accord-
ance with the circuit diagram.
Ensure that the device has been connected in accordance with
the circuit diagram.
Electronics fault. If the fault cannot be eliminated, inform the technical after-sales
service.
The displays flash The control panel is damp or an object is cover-
ing it.
Dry the control panel or remove the object.
The Ù indicator flashes in the
hotplate displays
A fault has occurred in the electronics. To acknowledge the fault, cover the control panel with your hand.
”ƒ
The electronics have overheated and have
switched off the corresponding hotplate.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
”…
The electronics have overheated and have
switched off all hotplates.
Ӡ + heat setting and acous-
tic signal
There is a hot pan in the area of the control
panel. There is a risk that the electronics will
overheat.
Remove the pan. The fault display goes out shortly afterwards.
You can continue to cook.
Ӡ and acoustic signal
There is a hot pan in the area of the control
panel. To protect the electronics, the hotplate
has been switched off.
Remove the pan. Wait for a few seconds. Touch any control. If the
fault display goes out, you can continue to cook.
”‚/”‡
The hotplate has overheated and switched itself
off to protect the work surface.
Wait until the electronics have cooled down sufficiently and
switch the hotplate on again.
”‰
The hotplate was operating for an extended
period without interruption.
The automatic safety switch-off function has been activated. See
section
“Š‹‹‹
“Š‹‚‹
The supply voltage is faulty; outside of the nor-
mal operating range.
Contact your electricity provider.
—…‹‹
The hob is not connected properly Disconnect the hob from the power supply. Ensure that it has
been connected in accordance with the circuit diagram.
Do not place hot pans on the control panel.
Customer service en
21
4Customer service
Cus t omer ser vi ce
Our after-sales service is there for you if your appliance
needs to be repaired. We will always find an
appropriate solution, also in order to avoid after-sales
personnel having to make unnecessary visits.
E number and FD number
Please quote the E number (product number) and the
FD number (production number) of your appliance
when contacting the after-sales service.
The rating plate bearing these numbers can be found:
■ On the appliance certificate.
■ On the lower section of the hob.
The E-number can also be found on the glass surface
of the hob. You can check the customer index (KI) and
FD number by going to the basic settings. Look up
section~ "Basic settings" for this.
Please note that a visit from an after-sales service
engineer is not free of charge in the event of misuse of
the appliance, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
GB 0344 892 8979
Calls charged at local or mobile rate.
IE 01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Loading ...
Loading ...
Loading ...