Loading ...
Call from the call log
1 Press .
2 Select a record and press .
View record
Press > [VIEW].
Save record
1 Press > [SAVE NUM.].
2 Follow on-screen instructions.
Delete record
1 Press > [DELETE].
2 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Meic:
MN0063-E060040
HuaJin:
HJ-0600400P1-EU
Frequently Asked Question
www.philips.com/support
Enter: Output:
Note
4
How to use
Phonebook
Call log
>
>
>
Redial
Note
1 Press .
2 Select [PHONEBOOK] > [ADD NEW].
3 Follow on-screen instructions.
Direct access memory
You have up to 2 direct access memories (keys 1 and
2). To dial the saved phone number automatically,
press and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are preset
to the voice mail number and information service
number of your service provider respectively
(network dependent).
Call from the redial list.
1 Press .
2 Select a record and press .
Save record
1 Press [SAVE NUM.].
2 Follow on-screen instructions.
Delete record
1 Press [DELETE].
2 Follow on-screen instructions.
> >
> >
Integrated answering
machine (for D166 Only)
Record an announcement
1 Press > [ANSWER & REC] >
[ANNOUNCEMENT].
2 Follow on-screen instructions.
Listen to the incoming messages
Press > [ANSWER & REC] > [PLAY].
Delete incoming messages
1 When you listen to the message, press to
enter the options menu.
2 Select [DELETE], then press to confirm.
Register additional handsets
You can register additional handsets to the base
station.
1 Press and hold key on the base station for
10 seconds.
2 Press .
3 Select [SERVICES] > [REGISTER], then press
to confirm.
4 Enter the system PIN/Passcode (0000).
5 Press to confirm PIN/Passcode.
Registration is complete in less than 2 minutes.
• You can recover the initial PIN/Passcode by
following this procedure.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press .
2 Select [SERVICES] > [RESET], then press
to confirm.
3 Follow on-screen instructions.
Technical
specifications
Battery
Philips: 2 x AAA NiMH 1.2 V Rechargeable 300mAh
batteries. Use only the supplied batteries.
Adapter (base and charger)
100-240V~,
50/60Hz, 200mA
100-240V~,
50/60Hz, 150mA
6V DC/
400mA
6V DC/
400mA
Phonebook: 50 entries
Call log: 20 entries
Talk time: 10 hours‚
Standby time: 200 hours‚
• You can install a DSL (digital subscriber line) filter to
prevent noise and caller ID problems caused by the
DSL interference.
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset is in [Unregistered] status, register
your handset. (See the section on “Register
additional handsets”).
If I fail to pair (register) the additional handsets to the
base station, what do I do?
• Your base memory is full. Select > [SERVICES]
> [UNREGISTER] to unregister the unused hansets
and try again.
• If registration fails, unplug the power adapter from
the base station and plug it back. Wait for 15
seconds, and then repeat the registration
procedure.
I have chosen a wrong language which I cannot read,
what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
UMS_D161/166
FR_FR_V1.0
This symbol on a product indicates that the
device is compliant with the European
Directive 2012/19/EU.
2019 © MMD Hong Kong Holding Limited
All rights reserved.
This product has been manufactured by and
is sold under the responsibility of MMD
Hong Kong Holding Limited. MMD Hong
Kong Holding Limited is the warrantor in
relation to this product.
Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips
N.V. and are used under license from
Koninklijke Philips N.V.
3 The following options will appear on the screen:
[TELEFOONINST] > [TAAL]
[PHONE SETUP] > [LANGUAGE]
[CONFIG. TÉL] > [LANGUE]
[TEL.-SETUP] > [SPRACHE]
[CONF. TELEF.] > [LINGUA]
4 Select them to access the language options.
5 Select your own language.
My handset is in searching or unavailable status,
what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail. What
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone connec-
tions.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. The battery icon animates when
charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply first and clean the contacts with a
damp cloth.
• Batteries are defective. Purchase new ones with
the same specifications.
Bad audio (crackles, echo, etc.)
• The handset is almost out of range. Move it
closer to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away.
The walls are too thick. Move the base station
away.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
»