We recommend that you use a professional
electrician to install the wall outlet. For information
about electrical specications, see SPECIFICATIONS.
SAFETY
Warnings:
• RISK OF ELECTRIC SHOCK — Use only in dry
locations and only indoors.
• All cables should be routed away from the
charger outlet openings.
• DO NOT use with any aquarium equipment.
• DO NOT install in an outlet that is not grounded.
Notes to the installer:
• This device must be installed in accordance with
National and Local electrical codes.
• To prevent severe shock or electrocution, always
turn power OFF at the service panel before
working with wiring.
• This device should be used with copper or
copper-clad wire. DO NOT use with aluminum
wire.
• DO NOT plug this device into a shallow wall box.
The wall box must be deep enough to house the
charger outlet. If the box is too shallow, the
charger outlet will not t securely into the wall.
PACKAGE CONTENTS
• 2 AC wall outlets
• White decora-style wall plate
• Screws: 2 long and 2 short
• Quick Setup Guide
FEATURES
• Replaces a standard duplex outlet
• Status LED lets you know your devices are
protected.
• Tamper-resistant outlets for added safety
• Provides two standard 125V power outlets
• Fireproof 1,080 joules surge protection
• Works in nearly all installations
• Compatible with your existing decora wall plate
Before using your new product, please read these instructions to prevent any damage.
INSTALLING THE CHARGER
1 Warning: DISCONNECT POWER. Failure to
do so can result in severe injury or death.
Make sure that you disconnect power to the
circuit by removing the fuse from the circuit
breaker or turning OFF the circuit breaker.
2 Remove the wall plate and mounting screws
that cover the old outlet.
3 Carefully remove the existing outlet from
the wall box.
4 Disconnect the wiring from the old outlet.
5 Connect the wires to the outlet:
• Black lead attaches to the hot wire
• White lead attaches to the neutral wire
• Green lead attaches to the ground wire
You can attach the wires by:
1 Inserting straight wires into the holes.
OR
2 Wrapping the wires 3/4 of the way around
the terminal screws, making sure that the
wires do not overlap.
3 Tighten every screw and make sure that no
bare copper wire is exposed. When
tightening screws, use 14 pounds-per-inch
of torque.
6 Carefully insert the outlet into the wall box.
QUICK SETUP GUIDE
Surge
Protector
NSHW120S18
PROTECTED/
FAULT
TR
AC
outlets (2)
Indicator
LED
Ground
(green)
Neutral
(white)
Hot
(black)
V1 ENGLISH 17-0258
7 Secure the outlet to
the wall box with the two
long screws (provided).
8 Secure the wall plate to the
outlet with the two
short screws (provided).
9 Restore power by
replacing the fuse or
turning on the circuit
breaker. The
outlet is ready to use.
USING THE WALL OUTLET
• To power electrical devices (like lamps or
notebooks), plug them into the electrical
outlets.
INDICATOR LED
• Green: surge protected
• Red: wiring fault
• LED o: not surge protected
Note: Only applicable if the outlet is receiving power.
The LED is not lit when power is shut o to outlet.
SPECIFICATIONS
Dimensions (L × W × H)
With plate:
4.7 × 3 × 1.9 in. (120 × 76 × 47.6 mm)
Without plate:
4.2 × 1.7 × 1.9 in (106 × 44 × 47.6 mm)
Electrical
Receptacle Rating: 15 Amp, 125VAC
Line Voltage: 125V A C @ 60 Hz
Surge protection: 3 lines (L-N / L-G / N-G)
Clamping voltage: L-N / L-G / N-G = 500 volts
Maximum surge current: 45,000 amps
Maximum energy dissipation: 1,080 joules
Wire Terminals: #14-#12 AWG
UL-1449 certied
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation. This equipment
has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment o and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Warning: Changes or modications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
ICES-003
This Class B digital apparatus complies with
Canadian ICES-003.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289 (U.S. and
Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2017 Best Buy. All rights reserved
Made in China
