Loading ...
Loading ...
Loading ...
2120
Operating the programmes
and special functions
Use in conjunction with programme guide
Setting a programme
Open the door press the button; the last
programme selected will appear on the display.
To set a new programme, press the Programme
Selection Button "P". When the required
programme is shown in the display, press the
"START" button. The time of the selected
programme (in hours and minutes) will start to
flash in the display.
Close the door and after an audible signal has
sounded (if it has not been deactivated) the
programme will start automatically.
Half load button
By pressing this button it is possible to wash a
small quantity of crockery using only the upper
basket for dishes and cutlery in the bottom
basket.
This reduces water and energy consumption
and requires a smaller quantity of detergent.
Please Note:
When the START Button has been selected it
is not possible to deselect it.
HPS button (High Pressure System)
Your dishwasher is fitted with a two speed
motor. By pressing the HPS Button, the motor
operates at a higher speed which will result in
higher water pressure, to attack the dirt.
The HPS option is particularly suitable for
washing pans, pots and heavily soiled crockery.
Please Note:
This option must be selected before pres-
sing the START button.
Economy button E
The "E" button reduces the final heating of the
water during the last rinse. This activates a
natural drying process, as with a normal
draining board, simply by leaving the door ajar
at the end of the cycle to enable the natural
circulation of air. The "E" button permits an
energy saving of more than 20% and shortens
the cycle.
Recommended for evening washes when the
dishes are not required perfectly dry, immediately,
straight after washing.
Interrupting a programme
It is not recommended that the door be opened
while a programme is running, and especially
not during the main wash phase and final
drying.
However, the appliance will stop automatically
when the door is opened.
At this point the various wash options can be
programmed or cancelled. The current program-
me can also be cancelled.
If, the door is opened during a programme, the
symbol for that programme will flash in the
display and the machine stops.
Please Note:
If you open the door during the drying cycle
an audible audio signal advises you that the
drying cycle has not yet completed.
To restart the machine, press the "START" button
and the time remaining for the programme will
flash. Now close the door.
If you wish to cancel or change a programme
that is running, carry out the following:
open the door keep the "START" button
pressed in until the number of the
programme stops flashing. A new
programme can now be set.
NB: If, on pressing the "START" button the
symbol "00" starts to flash on the display, it
means that there is water in the machine.
Close the door to allow the water to be
discharged and wait for the audible signal, after
which the new programme can be set.
Before starting a new programme, you should
check that there is still detergent in the dispenser.
If necessary, top up the dispenser.
End of programme
The end of the programme is indicated by an
audible signal (if it has not been deactivated).
When the door is opened the number of the
programme that has just finished will appear on
the display.
Important:
If the programme shown in the display starts
to flash and the machine will not let any more
programmes be selected, press the “START”
button and keep this button pressed until the
display stops flashing.
Delay Start programme button
To set the delay start programme press the
button.
On the first press the current setting appears on
the display. Each time the button is pressed the
delayed time in one hour increments increases,
up to a maximum of 19 hours.
Once set, wait until the selected time is confirmed
when it appears in the display. Press the "START"
button to start the countdown. If the countdown
has not already been activated, the delay start
can be cancelled by pressing the button
until the selected programme appears on the
display.
The delay start can be cancelled at any time
simply by keeping the "START" button pressed
in until the required wash cycle appears on the
display.
If you wish to see which programme has been
selected, press the "Programme Selection"
button “P”.
NB: If the door is opened during the countdown,
for example to select one of the options (or to
add more dishes), the "START" button should
be pressed before closing the door again, in
order to restart the countdown.
Activating and deactivating the audible
signal
The audible signal function can be deactivated
in the following way:
keep the Programme Selection Button (P)
pressed in for a few seconds and at the same
time press the stop/start button ; if the
symbol "b1" appears on the display the audible
signal is activated. Press the programme
selection button (P) again and the symbol "b0"
will appear which means that the audible signal
has been deactivated.
An audible signal sounds to indicate that the
setting has been stored in memory.
Attention
This dishwasher is equipped with an
anti-overflow safety device which works even
when power is off, and if the water level is too
high, the supply will automatically be closed off.
Important
To ensure the correct operation of the
anti-overflow safety device, it is recommended
not to move or to tilt the dishwasher during
operation.
If it is necessary to move or to tilt the
dishwasher, first make sure the washing cycle is
finished and that no water is left in the tank.
I
I
Display shows E1.
Display shows E2.
Display shows E3.
Display shows E4.
PROBLEM CAUSE REMEDY
The Dishwasher is able to self-assess a number of problems. The problem will
be illustrated in the display window and by an audible signal.
Water supply switched off.
Problem with electronic temperature
control.
The Water Heater Element does not
work properly or the filter mesh is
blocked.
The appliance does not discharge
water.
Switch off appliance.
Turn on water supply.
Reset the cycle.
Call Service for assistance.
Clean the Filter Mesh and if the
problem continues please contact
Service.
Check :
• That the discharge hose is not
bent
• Syphon is not blocked
• Filters are not blocked
PROBLEMS AUTOMATICALLY SIGNED
Loading ...
Loading ...
Loading ...