Loading ...
Loading ...
SB-T-TACCAB/10W3v3_INSTR_SKU#011230
SB-T-TACCAB/10W3v3_INSTR_SKU#011230
CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
STEP 10
Place the screws and cup holders that were removed
in STEP 1.
STEP 11
Place the supplied L-bracket onto the Stealthbox®, as in the
picture.
With a 7/64-inch drill bit and drill, drill pilot holes into the
Stealthbox® only. With the supplied screws, mount the
L-bracket to the Stealthbox® and to the center console.
Place the supplied black carpet panels into the storage
bucket and the rear cup holder areas.
STEP 10
Place the center console on top of the Stealthbox.
This rear portion of the console has ears that stick out the
front on the side walls. These ears need to be placed into the
inside of the walls of the front position of the console.
Page 3 • JL Audio, Inc 2006
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011230-05-07-200
JLA-SKU#011230-05-07-200
7
7
• Printed in USA • ©2005 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
INCLUDED HARDWARE
(3)
(3)
1/4-inch -20 x 1-1/2-inch Hex Bolts
1/4-inch -20 x 1-1/2-inch Hex Bolts
(2)
(2)
Custom Short Mounting Bracket
Custom Short Mounting Bracket
(3)
(3)
1/4-inch x 3/4-inch US
1/4-inch x 3/4-inch US
S Flat Washer
S Flat Washer
(1)
(1)
Aluminum L-Bracket
Aluminum L-Bracket
(3)
(3)
1/4-inch x 1 1/4-inch Lock Washer
1/4-inch x 1 1/4-inch Lock Washer
(
(
3)
3)
Flat Head Machine Screws
Flat Head Machine Screws
(1)
(1)
Custom Long Mounting Bracket
Custom Long Mounting Bracket
SPECIFICATIONS
Enclosure Type:
Acoustic Suspension (sealed)
Acoustic Suspension (sealed)
Driver Type:
10W3v3-4
10W3v3-4
Nominal Impedance:
4 ohms mono
4 ohms mono
Continuous Power Handling:
300 Watts
300 Watts
POWER RECOMMENDATION
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when
being used to power your Stealthbox
®
.
JL AUDIO 250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch.
Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch.
Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1
+13
+3
+7
+10
Preamp Output Section
+12VDC Ground Remote
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6-inch x 9-inch Separates / Front Doors
6-inch x 9-inch Separates / Front Doors
Fits JL Audio Models*:
TR690-TXi & VR690-CSI
TR690-TXi & VR690-CSI
Rear Speaker Size / Location:
6.5-inch / Rear Doors
6.5-inch / Rear Doors
Fits JL Audio Models*:
TR650-CXi, TR650CSi, VR650-CXi, VR650-CSi,
TR650-CXi, TR650CSi, VR650-CXi, VR650-CSi,
XR525-CXi, XR525-CSi, C5-525x, C5-525 & ZR525-CSi
XR525-CXi, XR525-CSi, C5-525x, C5-525 & ZR525-CSi
* All speakers require custom adaptors for installation
* All speakers require custom adaptors for installation