Loading ...
Loading ...
Loading ...
6 49-5000437 Rev. 1
USING THE AIR CONDITIONER
Controls
Remote Control
Ŷ7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW
the signal receiver on the air conditioner.
Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG
the remote control that could block the signal.
Ŷ7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRIXSWR
feet.
Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\
as indicated on the remote control.
Cool Mode
8VHWKH&RROPRGHDWLow, Med, High or Auto Fan
6SHHGIRUFRROLQJ8VHWKHTemperature Increase + /
Decrease – pads to set the desired temperature between
62°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air will
become cooler. Set the thermostat at a higher number
and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on
while set to a Cool setting or if turned from a fan setting
to a Cool setting, it may take approximately 3 minutes for
the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and High
or Med fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode and
High fan with a lower set temperature.
For Quieter and Nighttime Cooling—Select the Cool
mode and Low fan with a middle set temperature.
Sleep Pad
The SLEEP mode sets the unit to gradually change
settings over an 8 hour period to allow for some
increased energy efficiency during sleep hours.
The SLEEP mode is available only in AUTO and
COOL settings.
Press the SLEEP mode pad and its light will
illuminate. The air conditioner will automatically
change the fan speed to AUTO.
In COOL mode, the fan will stay in the AUTO speed
setting for 8 hours from the time the SLEEP mode
pad was pressed. The air conditioner will also
raise the set point 2°F in 30 minutes and 2°F more
in another 30 minutes where it will remain for the
next 7 hours. After 8 hours, the air conditioner will
resume the settings that were in place before the
SLEEP mode pad was pressed.
While the unit is in SLEEP mode, pressing the
SLEEP pad again will return it to the settings that
were in place before the SLEEP mode pad was
pressed.
Timer Pad
Press Timer pad, the Timer On or Timer Off
indicator light illuminates. It indicates the Auto Start
or Auto Stop program is initiated. For some units,
keep pressing the Timer pad will cancel the timer
settings.
Press or hold the Increase + /Decrease – pads to
change the Auto time by 0.5 hour increments, up to
10 hours,then at 1 hour increments up to 24 hours.
The control will count down the time remaining until
start.
The selected time will register in 5 seconds, and the
system will automatically revert back to display the
previous temperature setting or room temperature
when the unit is on (when the unit is off,there is no
display.)
Turning the unit On or Off at any time or adjusting
the timer setting to 0.0 will cancel the Auto Start/
Stop timed program.
Filter Pad
Press Filter pad to initiate this feature. This feature
is a reminder to clean the Air Filter for more
efficient operation. The LED(light) will illuminate
after 250 hours of operation. To reset after cleaning
the filter, press the Filter pad and the light will go
off.
Eco Pad
Press Eco pad to initiate this function. This function
LVDYDLODEOHRQ&22/'5<$872RQO\$872
&22/,1*DQG$872)$1PRGHV7KHIDQZLOO
continue to run for 3 minutes after the compressor
shuts off. The fan then cycles on for 2 minutes
at 10 minute intervals until the room temperature
is above the set temperature, at which time the
compressor turns back on and cooling starts.
Loading ...
Loading ...
Loading ...