Loading ...
Loading ...
Loading ...
5. I f you find your refrigerator rocks from corner to
corner, it means your floor is uneven. Find a piece
of plastic or hardboard etc. and pack it firmly
under the roller.
6. You may now need to fine-tune the installation by
repeating steps 3, 4 and 5.
7. When you have the appliance in its final position,
it needs to be stabilised. Wind the stability foot
under the door hinge down to the floor until it just
makes contact with the floor. Lift the front of the
appliance to take the weight off the stability foot,
then turn it half a turn further to ensure firm
contact with the floor. Wind the large height
adjusting nut back up to ensure all the weight is
now on the front stability foot.
8. Repeat step 7 for the stability foot on the handle
side. Whenever you need to move the appliance,
be sure to wind the feet back up so that the
appliance can roll freely and be sure to reset it
when reinstalling.
stability foot
wound down
Large height
adjusting nut
wound up.
9. Plug your refrigerator straight into its own power
point and never use a double adapter. If you
need to roll the refrigerator to get to the plug,
remember to raise the stability foot first.
10. Before you put any food in your refrigerator, it’s
recommended you leave it on for 2 or 3 hours to
check it is running properly.
FITTING THE HANDLES
For models with ‘Pole’ handles, the handles are
supplied prepackaged with your refrigerator and will
require fitting.
Refer to the instructions provided in the pack.
Congratulations! You have successfully installed your
new refrigerator.
1 x water filter with push fit connections
2 x mounting brackets and screws
4 + 1 metres of water tubing
1 x 1/2” tap fitting
DATE FITTED___/___/___
2 x circlips
Filter Kit for single door freezer
Installation Kit
Bottom mount &
single door all refrigerator)
4 metres of water tubing
1 x 1/2” tap fitting
Water supply and plumbing
A drinkable water supply to suit a 1/2” tap fitting is
required adjacent to the refrigerator. It is
recommended that a licensed plumber install a new
water supply outlet nearer to the appliance should the
tubing supplied not be long enough. It is not
recommended that the tubing be extended as this
could adversely affect the flow of water to the ice
maker or water dispenser. The water dispenser and
automatic ice maker require a drinkable water supply
with a pressure range of between 206kPa and 689kPa
(30PSI and 100PSI). If the water supply is above 100psi
a pressure limiting valve should be installed.
ICE AND WATER MODELS
WARNING
Connect to potable water supply only, if using tank or
bore water in a model with an internal filter it is
recommended to also use an external filter
(not supplied).
The new hose sets supplied with the appliances must be
used and old hose sets should not
be reused.
Never connect the appliance to a hot water supply.
WATER FILTER
It should not be used on water that is micro biologically
unsafe or with water of unknown quality. The service life
of the filter may be reduced in water supplies that
contain an excess of particles or other impurities.
Reduced flow rate is an indication that a new filter is
required. Failure to replace the filter when required can
affect the function of the ice maker. Service calls caused
by a failure to replace the filter are not covered by
warranty. Replacement water filters
are available from Electrolux Home Products Spare Parts
Centres and can be posted to you for your convenience
(refer to spare parts contact numbers on the warranty
page).
Contents of installation kits
11
4. Check the alignment of the refrigerator to the
surrounding cupboards to see if it is level. You can
adjust the level as detailed in step 2 and 3.
adjust front feet for
uneveness of floor
eg. wind this foot
down or up.
top of refrigerator is
level ie horizontal.
aligned to
cupboards
ie even gap.
Loading ...
Loading ...
Loading ...