Loading ...
Loading ...
Loading ...
5
OPERATING INSTRUCTIONS
Sanitize Option
To sanitize your dishes and glassware, select
SANITIZE option. When selected, the light
above the pad will come on and reamin on until
end of cycle. The water temperature in the
fi nal rinse will be raised to 155
o
F (68
o
C) and
will maintain that temperature for 9 minutes.
This option is available in Heavy and Normal
Cycles. Only these sanitization cycles have ben
designed to meet NSF requirements.
The cycle time will be extended until the proper
water temperature is reached.
Washing
action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120
o
F (49
o
C).
The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120
o
F
(49
o
C).
To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off.
Delay Start
The DELAY START option allows you to
automatically delay starting your dishwasher
from 2-4-6, 1-10 or 1-24 hours depending on
your model.
On models with 1-10 or 1-24 hour delay, press
the DELAY START pad until the desired delay
time shows in the STATUS window. A light will
come on indicating the delay start hours and
will remain on until cycle starts.
On models with 2-4-6 hour delay, press the pad
once for a 2 hour delay, twice for 4 hours and
three times for 6 hours. A light will come on
indicating the delay start hours and will remain
on until cycle starts.
To cancel the DELAY START option and begin
the cycle before the delay period is over, press
the START/CANCEL pad.
Heat Dry/Air Dry
Use the HEAT DRY option, especially in
combination with use of rinse agent, will
enhance drying. If AIR DRY is selected the
heater will be de-activated during the drying
phase of the selected wash cycle. This will
slightly lower the energy use but will increase
the likelihood that the dishware will not dry
completely.
Child Lock Controls
To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, lock the dishwasher controls
by pressing and releasing the AIR DRY pad
(some models) or the RINSE ONLY pad (some
models) for 8 seconds while the door is
latched. An indicator light on the lock graphic
pad will illuminate when the controls are locked
and no new selections can be made until the
lock is released. To unlock the controls, press
the same pad, AIR DRY or RINSE ONLY, until
the indicator light goes out.
To Cancel a Cycle
You can cancel a cycle anytime during the
cycle. Press START/CANCEL pad and the
dishwasher will start a 90 second drain. At the
end of the drain, select the next desired cycle.
Wash Cycle Selections
Cycle times are approximate and will vary with
options selected. Hot water is necessary to
activate dishwasher detergent and melt fatty
food soils. An automatic sensor will check
the incoming water temperature and, if it is
not hot enough, the cycle will be lengthend
for automatic water heating in the main wash
and fi nal rinse of all cycles. This happens
even when HI-TEMP WASH option has not be
selected. When HI-TEMP WASH is selected,
an even higher temperature will be reached to
handle heavier soil loads.
Option Selections
Hi-Temp Wash Option
When HI-TEMP WASH option is selected, the
dishwasher heats water in the main wash to
approximately 140
o
F (60
o
C).
This increase in water temperature helps the
dishwasher detergent remove food grease and
soil from dishes more effectively and aids in
drying. HI-TEMP WASH option can be used with
all cycles except RINSE ONLY. HI-TEMP WASH
is automatically provided when the HEAVY
WASH cycle is selected.
When HI-TEMP WASH option is selected, the
light above the pad will come on and remian
on until end of cycle. To turn off the HI-TEMP
WASH option, press the pad a second time.
The light above the pad will turn off.
Loading ...
Loading ...
Loading ...