Loading ...
Loading ...
Loading ...
4
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
DELAY
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
1.Press the DELAY button: the corresponding symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2.Select the wash program and close the door: the timer
will begin counting down;
3.Once this time has elapsed, the indicator light switches
off and the wash cycle begins.
To adjust the delay time and select a shorter period of
time, press the DELAY button. To cancel it, press the
button repeatedly until the selected delayed start
indicator light switches off.
The wash program will start automatically as soon as the
door is shut.
The Delay function cannot be set once a wash cycle
has been started.
ZONE WASH 3D
Thanks to the additional 3D water jets placed on the
bottom of the cavity, 3D ZONE WASH option allows to
save energy or to increase the washing performance of
the dishwasher.
It is compatible with Normal and Intensive cycles, and it
works with one rack at once.
• 3D ZONE WASH + NORMAL CYCLE: it allows to reduce
energy consumption up to 40%.
• 3D ZONE WASH + INTENSIVE CYCLE: it increases the
washing performances up to 40%. Ideal for very soiled
mixed loads, e.g. pans and saucepans, dishes with
heavy encrustation or difficult-to-clean crockery
(grater, vegetable mill, dirty cutlery).
How to activate the option:
1. Select a compatible cycle
2. By default the appliance washes dishes in all racks. To
wash only the specific rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the crockery in the selected rack
only.
TABLET (Tab)
This setting allows you to optimize the performance of
the program according to the type of detergent used.
Press the TABLET button (the indicator light will light up)
if you use combined detergents in tablet form (rinse aid,
salt and detergent in 1 dose).
If you use powder or liquid detergent, this option
should be off.
TURBO
This option can be used to reduce the duration of the
main programs while maintaining the same washing and
drying performance levels.
After selecting the program, press the TURBO button and
the indicator light will switch on. To deselect the option,
press the same button again.
EXTRA DRY
To improve the drying of the dishes, after selecting the
program, press the EXTRA DRY button and the indicator
light comes on.
A higher temperature during the final rinse and an
extended drying phase allow for improving drying. To
deselect the option, press the same button again. The
EXTRA DRY option results in the lengthening of the wash
cycle.
LIGHT POINT
Some dishwasher models are equipped with a green
indicator light in the gap between the door and kitchen
top providing information on the phase of the current
wash cycle. One of the following operating modes can be
selected:
a) Disabled function
b) When the cycle starts the light goes on for few seconds,
stays off during the cycle and flashes at the end of the
cycle (default mode).
c) The light stays on during the cycle and flashes at the end
of the cycle.
If the delayed start was set, the light goes on either for the
first few seconds or the entire duration of the countdown,
based on whether mode b) or c) was set.
The light goes off every time the door is opened. To select
the mode you prefer, switch on the machine, hold down
button P until one of the three letters appears on the
display, press button P until you reach the desired letter (or
mode), hold down button P to confirm the selection.
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps
will sound. The option will not be enabled.
Loading ...
Loading ...
Loading ...