Loading ...
Loading ...
7 Clean the guards under a warm tap
(Fig. 20).
8 Carefully shake o excess water and let
all parts air dry completely.
Cleaning the nose trimmer
Clean the nose trimmer immediately after
use and when a lot of hair or dirt has
accumulated on the nose trimmer head.
1 Rinse the nose trimmer head with hot
water (Fig. 21).
2 Turn on the product and rinse the nose
trimmer head once more to remove
any remaining hairs. Then turn o the
product again.
For a thorough clean, immerse the nose
trimmer head in a bowl with warm water
for a few minutes and then turn on the
product to remove stubborn hair/debris.
Hold the appliance upside down and
make sure the handle does not get wet
during this process.
3 Carefully shake o excess water and let
all parts air dry completely.
This product has no other user-
serviceable parts. For assistance call
1-800-243-3050.
Storage
- Store the product in the pouch
supplied. Make sure the product is dry
before you store it in the pouch.
- Be sure the product is turned o.
Remove cord from outlet and the
product before storing it in a safe, dry
location where it will not be crushed,
banged, or subject to damage.
- Do not wrap cord around the product
when storing.
- Store cord in a safe location where it
will not be cut or damaged.
- Do not place or store the product where
it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
Accessories
Replacement parts and accessories may
be purchased at a store near you or on our
website www.philips.com/store.
Trimming ear hair
1 Slowly move the tip round the ear to
remove hairs that stick out beyond the
rim of the ear.
2 Gently move the tip in and out of the
outer ear channel to remove unwanted
hairs (Fig. 17).
Cleaning
Do not rinse the handle under the tap,
only the attachments can be rinsed under
the tap.
Never use scouring pads, abrasive
cleaning agents or aggressive liquids
such as gasoline or acetone to clean the
product.
Never dry the trimmer teeth with a towel
or tissue, as this may damage the trimmer
teeth.
Cleaning after every use
1 Turn o the product and disconnect
from the power outlet.
2 Remove any guard (see ‘Attaching and
detaching guards’) or cutting element
(see ‘Detaching and attaching cutting
elements’) from the product.
3 Remove any hairs that have
accumulated in the hair chamber with
the cleaning brush supplied.
4 Clean the cutting element and guard
under a warm tap (Fig. 18).
The handle is not suitable for cleaning
under the tap.
5 Carefully shake o excess water and let
all parts air dry completely.
Thorough cleaning
1 Turn o the product and disconnect
from the power outlet.
2 Wipe the handle of the product with a
dry cloth.
3 Remove any guard (see ‘Attaching and
detaching guards’) or cutting element
(see ‘Detaching and attaching cutting
elements’) from the product.
4 Remove any hairs that have
accumulated in the hair chamber with
the cleaning brush supplied.
5 Remove any hairs that have accumulated
in the cutting elements and/or guards
with the cleaning brush supplied.
6 Clean the cutting elements under a
warm tap (Fig. 19).
The handle is not suitable for cleaning
under the tap.
Fading hair guard
Attach the fading hair guards to the extra-
wide hair trimmer to trim the hair around
the ears with a faded result. The product
comes with 2 guards. Use both guards to
trim hair around both ears. Choose a hair
guard based on the preferred trimming
direction of back to front or front to back.
Always make sure that you hold the side
of the guard with the short teeth closest to
your ear.
Guard inch mm
Fading hair
guards
5/32in.-
23/64”
4-9mm
1 Attach the guard to the extra-wide hair
trimmer to trim the hair around the ear.
Then attach the other guard to trim the
hair around the other ear.
2 Place the product on your hair at the
back or front of your ear, depending
on the trimming direction you prefer.
Always make sure that the side of the
guard with the short teeth is closest to
your ear.
3 Move the trimmer slowly around the
ear, while holding it steady (Fig. 15).
For best results, move the trimmer
against the direction of hair growth
(back to front).
Precision attachments for use
on face
Precision trimmer
Use the precision trimmer to create ne
lines and contours around your facial
style, close to the skin (to a length of
1/32in (0.5mm)).
1 Hold the precision trimming head
perpendicular to the skin and move the
trimming head upwards or downwards
with gentle pressure (Fig. 16).
Nose trimmer
Use the nose trimmer to trim your nose
hair and ear hair.
- Make sure nasal passages are clean.
Make sure outer ear channels are clean
and free from wax.
- Do not insert the tip more than 3/16in
(0.5cm).
- Always clean the attachment after
each use.
Trimming nose hair
1 Gently move the tip in and out of nose
while turning it around to remove
unwanted hairs (Fig. 17).
1 Attach a body guard to the full-size hair
trimmer (see ‘Attaching and detaching
guards’).
2 To trim in the most eective way,
stretch the skin with your free hand and
move the guard against the direction
of hair growth (Fig. 12). Make sure the
surface of the guard always stays in
contact with the skin.
Attachments for use on head
Extra-wide hair trimmer
Use the extra-wide hair trimmer without
a guard to clip the hair on your head very
close to the skin (1/32in (0.5mm) or to
contour the neckline and area around
the ears.
1 To contour the hairline around the ears,
comb the hair ends over the ears.
2 Tilt the product in such a way that only
one edge of the cutter blades touches
the hair ends when you shape the
contours around the ears.
3 To contour the nape of the neck or
sideburns, turn the product and make
downward strokes (Fig. 13).
4 Move the product slowly and smoothly
following the natural hairline.
Hair guards
Attach a hair guard to the extra-wide hair
trimmer to evenly trim the hairs on your
head. The product comes with
4 hair guards. The hair length settings
are indicated on the guards. The settings
correspond to the remaining hair length
after trimming.
Guard inch mm
Hair guard 5/32in. 4mm
Hair guard 3/8in. 9mm
Hair guard 15/32in. 12mm
Hair guard 21/32in. 16mm
1 Attach a guard to the extra-wide hair
trimmer.
2 Move the trimmer slowly over the
crown from dierent directions to
achieve an even result. Make sure the
surface of the guard always stays in
contact with the skin.
- Always move the trimmer against
the direction of hair growth (Fig. 14).
Press lightly.
- Make overlapping passes over the
head to ensure that all hair that
should be cut has been cut.
Loading ...