Loading ...
Loading ...
Loading ...
> Before Start > Part Names > Install > Initial Setup > Playback
Supplementary information | Advanced Setup |Others
33
En
0 Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32 kHz,
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 20 bit, 24 bit, 176.4 kHz, 192 kHz/16 bit,
20 bit, 24 bit.
2. Main Volume
3. Hardware
COAX2 "BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE",
"PHONO": Allocate an input selector to the DIGITAL IN
COAXIAL 2 jack. (Default Value is "CBL/SAT")
OPT1 "BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE",
"PHONO": Allocate an input selector to the DIGITAL IN
OPTICAL 1 jack. (Default Value is "GAME")
OPT2 "BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE",
"PHONO": Allocate an input selector to the DIGITAL IN
OPTICAL 2 jack. (Default Value is "TV/TAPE")
Max Vol Set the maximum value to avoid too high volume. Select "Off
(default value)" or a value between "50" to "99".
POn Vol Set the volume level of when the power is turned on. Select
"Last (default value)" (volume level before entering standby
mode), "Min", "0.5" to "99.5" and "Max".
0 You cannot set a higher value than that of "Max Vol".
HP Lvl Adjust the output level of the headphones. Select from
"-12.0 dB" to "+12.0 dB". (Default Value is "0.0 dB")
SpImpedance Set the impedance (≠) of the connected speakers.
"4Ω": When any of the connected speakers have 4 ≠ or more to
less than 6 ≠ impedance, or when speaker systems are
connected to both of the SPEAKERS A/B terminals
"6Ω (default value)": When the connected speakers all have 6 ≠
or more impedance
0 Note that when connecting to both SPEAKERS A and B
terminals, connect speakers with 8 ≠ to 16 ≠ impedance to
both A and B.
0 For impedance, check the indications on the back of the
speakers or their instruction manual.
Auto Stby This setting places the unit on standby automatically after 20
minutes of inactivity without any audio input. (When "NET Stby"
is on, this becomes the Hybrid Standby mode which reduces the
increase in power consumption to a minimum.)
"On": The unit will automatically enter standby mode. "AUTO
STBY" lights on the display.
"Off": The unit will not automatically enter standby mode.
0 "Auto Stby" is displayed on the display 30 seconds before the
Auto Standby comes on.
0 "Auto Stby" does not work when ZONE 2 is active.
0 Default values vary depending on the regions.
NET Stby When this feature is turned "On (default value)", you can turn on
the power of the unit via the network using an application that
can control this unit.
0 When using "NET Stby", power consumption increases even
when this unit is on standby, however, the increase in power
consumption is kept to a minimum by automatically entering
the Hybrid Standby mode, where only essential circuits are
operating.
0 When the connection to the network is lost, "NET Stby" is
disabled to reduce power consumption. Use the power button
on the remote controller or main unit to turn the unit on if this
happens.
SN29403237B_DTM-6_En_1802XX.book 33 ページ ２０１８年２月２８日 水曜日 午後４時５４分
Loading ...
Loading ...
Loading ...