Loading ...
Loading ...
Loading ...
Vertical steam ironing
•
Hang the garment on a hanger and hold the fabric slightly taut with one hand. The
steam is very hot, so you should always do this with the garment on a hanger – never
i
ron clothes which someone is wearing.
• Set the thermostat control to
“MAX” – fig.8.
• Operate the Power zone trigger by pulsing – fig.7 moving the iron from top
t
o bottom – fig.9.
Dry ironing
• Set the temperature for the fabric to be ironed.
• Set the steam control to – fig.1.
• You may start ironing when the thermostat light goes out.
Extra Functions
Autoclean Catalys
®
Soleplate (depending on model)
• Your iron is equipped with a self-cleaning soleplate which works by catalysis.
• Its exclusive coating helps continuously eliminate all the impurities generated by normal use.
• It is recommended that you always stand your iron on his heel to preserve its self-cleaning coating.
Integral anti-scale system
Your iron is equipped with an integral anti-scale system. This system will help to provide:
• a better ironing quality with a constant flow of steam,
• lasting performance from your appliance.
Auto-Stop safety feature (depending on model)
• The electronic system cuts off the electric power and the Auto-Stop warning light flashes
if the iron is left vertically on its heel for more than 8 minutes, or in a horizontal position
for more than 30 seconds – fig.10.
• To restart the iron, just move it gently until the warning light stops flashing.
Anti-drip function (depending on model)
• When the iron is no longer hot enough to produce steam, the water feed will stop automatically to avoid dripping.
Maintenance and cleaning
Cleaning the anti-scale valve (once a month)
• Unplug your iron and empty the water tank.
• Adjust the steam setting to “Eco”.
• To remove the anti-scale valve, open the water tank lid and press the release button
– fig.11 and then pull the valve upwards – fig.12.
• Soak the valve in a cup of white spirit vinegar or plain lemon juice for 4 hours - fig.14.
• Rinse the valve under running water.
• Replace the anti-scale valve; press until it clicks in to place – fig.15.
Self-cleaning
• Fill the tank of your iron with untreated tap water. Stand the iron on it’s heel
with the thermostat set to “Max” and heat it up.
• When the thermostat light goes out, unplug the iron and hold it in a horizontal
position, over a sink. Remove the anti-scale valve – fig.11-12 (see previous
chapter).
• Shake the iron gently, over the sink, until some of the water in the water tank
(with the impurities) has flowed out through the soleplate – fig.16.
• At the end of the operation, replace the anti-scale valve; press it in until it clicks – fig.15.
• Plug the iron back in and leave it resting on its heel for two minutes to dry the soleplate.
• Clean the soleplate with a damp, non-metallic cloth while it is still warm.
Cleaning the soleplate
Your steam iron is fitted with a self-cleaning soleplate (depending on model):
• The exclusive active coating helps continuously eliminate all the impurities generated by the normal day-to-
day use of the iron.
• However, if you iron using an unsuitable programme, some traces may be left which require manual cleaning.
3
The auto-stop
light will be lit
during normal
use!
Be careful!
- Never touch the
end of the valve –
fig.13.
- The iron will not
function without the
anti-scale valve.
The self-cleaning
function helps to slow
down scaling in your
iron. In order to extend
the life of your iron, use
the Self-Cleaning
function once a month.
Hold the iron a few
centimetres from the fabric
to avoid burning delicate
fabrics.
Every five pulses return the
iron to a horizontal position.
1800121666FV53XXX0FTNTF_110x15406/06/1109:17Page3
Loading ...
Loading ...
Loading ...