Loading ...
SB-H-RIDGLNE/10W3v3_ 011214
STEALTHBOX WALL
THREADED INSERT
VEHICLE SHEET METAL
FENDER WASHER
SOCKET CUP SET SCREW
LOCK WASHER
FLAT WASHER
HEX NUT
CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
STEP 6
From under the vehicle, place the supplied fender washer,
flat washer, lock washer and then hex nut onto the protrud-
ing socket cup set screw. Secure tightly with a 14mm socket,
long extension and rachet.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
STEP 5
(A) Loosen the socket cup set screw to expose 1-1/2-inch.
Place the enclosure into place, carfully guiding the socket
cup set screw through the drilled hole. .
(B) Run speaker wire from the amplifier location to the
Stealthbox® and attach to the terminal
Double check the woofer for proper operation.
STEP 4
A Posistion the Stealthbox® into place and press firmly
down. This is to make an impression onto the wax square.
Remove the Stealthbox®.
B With a 1/2" drill bit or StepBit/Unibit® and drill. Drill at the
impression on the wax square, through the metal floor to the
outside.
(C) Remove the wax sqaure.
Page 2 • JL Audio, Inc 2006
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011214-07-2006 • Printed in USA • ©2006 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
INCLUDED HARDWARE
(1) 3/8-inch - 16 Hex Nut (1) 3-inch x 3-inch Wax Square
(1) 3/8-inch x 3/4-inch USS Flat Washer (1) 3/8-inch - 16 x 2-1/4-inch Socket Cup Screw
(1) 3/8-inch x 1-1/4-inch Fender Washer
(1) 3/8-inch Lock Washer
SPECIFICATIONS
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W3v3-4
Nominal Impedance: 4 ohms mono
Continuous Power Handling: 300 Watts
POWER RECOMENDATION
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when
being used to power your Stealthbox
®
.
JL AUDIO 250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch.
Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch.
Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1
+13
+3
+7
+10
Preamp Output Section
+12VDC Ground Remote
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5-inch / Front Doors
Fits JL Audio Models: TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi & ZR650-CSi
Rear Speaker Size / Location: 6.5-inch / Rear Deck
Fits JL Audio Models: TR650-CXi, VR650-CXi & XR650-CXi