Loading ...
Loading ...
Loading ...
14 49-5000406 Rev. 7
Installation Instructions
INSTALLATION INSTRUCTIONS
E2. MECHANICAL NON-DUCTED
INSTALLATION (RARMN_ _)
1. Remove the 6-pin connector cover from the
ceiling assembly by removing 2 screws.
2. Plug the cord with 6-pin connector into the 6-pin
receptacle on the mounting template.
3. Reinstall the 6-pin connector cover, routing the
FRUGWKURXJKWKH8VKDSHGRSHQLQJDQGWDNLQJ
care not to pinch the wires.
8QLQVWDOOWKHMXQFWLRQER[FRYHUE\UHPRYLQJ
screws.
5. Route the 115 VAC power supply cord through
the 2-screw strain relief of the ceiling assembly.
Then, tighten the strain relief, taking care not to
damage the wires.
8VLQJZLUHFRQQHFWRUVUDWHGIRU\RXUZLUHJDXJH
connect line to black, neutral to white, and
ground to green.
8VLQJHOHFWULFDOWDSHVHFXUHWKHFRQQHFWRUVWR
prevent any potential movement due to vehicle
vibration. If wire nuts are used, be sure to apply
the tape in the direction the nut was tightened so
as to not unintentionally loosen the connection.
8. Position the power supply wires and connections
inside the junction box and reinstall the junction
box cover.
9. Align the plastic ceiling panel to the mounting
template using the control knob posts as guides.
10. Install the 2 control knobs, ensuring the
D-shaped contour is properly aligned on the
posts.
11. Proceed to step 9 of Section E1.
E3. ELECTRONIC NON-DUCTED
INSTALLATION (RAREN_ _ &
RPREN__)
8QLQVWDOOWKHEODQNLQJSODWHIURPWKHPRXQWLQJ
template by removing 3 screws
2. Mount the main control box (RAR_C) to the
mounting template using 2 screws.
3. Remove 3 screws from the base of the main
control box, allowing the base to hinge open.
The control board is now visible and accessible.
4. Route the 115 VAC power supply cord through
the strain relief of the ceiling assembly. Then,
tighten the strain relief, taking care not to
damage the wires.
8VLQJZLUHFRQQHFWRUVUDWHGIRU\RXUZLUHJDXJH
connect line to black, neutral to white, and
ground to green.
E3. ELECTRONIC NON-DUCTED
INSTALLATION (RAREN_ _ &
RPREN__)
(cont.)
6. Connect the 6-pin power cord to the 6-pin
receptacle in the main control box.
8VLQJHOHFWULFDOWDSHVHFXUHWKHFRQQHFWRUVWR
prevent any potential movement due to vehicle
vibration. If wire nuts are used, be sure to apply
the tape in the direction the nut was tightened so
as to not unintentionally loosen the connection.
8. The indoor coil freeze sensor should be installed
in the thermistor well on the rooftop unit (image
on right). The sensor has a 2-pin connector that
needsto be plugged into the T2 terminal on the
control board. Heat-pump models also have a
4-pin connector that needs to be plugged into
the T3/T4 terminal on the control board.
9. If you are using your system with the RARES1A
room sensor, you will need to connect the
pigtail provided with the RARES1A kit to the
7WHUPLQDO8VLQJZLUHFRQQHFWRUVFRQQHFW
intermediary wires to the pigtail which will
connect the pigtail to the sensor.
10. OPTIONAL: If you want your AC to be
connected to your RV’s load shed system (not
included with all RVs), first connect the provided
3-pin pigtail to the T5 terminal. Then, using wire
connectors, connect the two pigtail wires to your
RVs load shed system. Refer to your RV/load
shed system’s user manual.
11. OPTIONAL: If you have a furnace you would
like to control via your thermostat, using wire
connectors, connect the two blue wires to your
furnace. Refer to your furnace’s owner manual.
12. OPTIONAL: Some main controls have auto
generator start functionality. If you want to
enable this function, using wire connectors,
connect the two yellow wires to your generator.
Refer to your generator’s user manual.
13. Keeping all connections inside the control box,
URXWHWKHZLUHVWKURXJKWKH8VKDSHGRSHQLQJ
on the side. Then, taking care not to pinch/crush
any wires, rotate the base of the main controlbox
upward and reinstall the 3 screws removed in
Step 3 to seal the control box.
14. Install the cover plate via 3 screws that attach
to the mounting template and 2 screws that that
attach to the main control box.
Loading ...
Loading ...
Loading ...