Loading ...
Loading ...
Loading ...
4 49-5903-3
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
If you are not familiar with electrical power and procedures, call a qualified electrician.
7KHSRZHUFRUGDQGRUFRQQHFWLRQVPXVWFRPSO\ZLWK
WKH1DWLRQDO(OHFWULFDO&RGH6HFWLRQDQGRUORFDO
codes and ordinances.
For Models Not Equipped with a Cord:
If your disposer does not come equipped with a cord,
you can connect it in two ways:
1. Attach a power cord, minimum 18” in length and
QRWWRH[FHHG´LQOHQJWK8VH*($3DUW1XPEHU
30;
or
2. Wire the disposer directly into the house current.
To Attach a Power Cord:
GROUNDING INSTRUCTIONS: 7KLVGLVSRVHUPXVW
be grounded to reduce the risk of electric shock in
the event of a malfunction or breakdown. Grounding
provides a path of least resistance for electric current.
7KLVGLVSRVHULVHTXLSSHGZLWKDFRUGKDYLQJDQ
equipment-grounding conductor and a grounding
SOXJ7KHSOXJPXVWEHSOXJJHGLQWRDQRXWOHWWKDWLV
properly installed and grounded in accordance with all
local codes and ordinances.
WARNING
Improper connection of the
equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the appliance is properly grounded.
NOTE: 'LVFRQQHFWHOHFWULFSRZHUWRGLVSRVHUFLUFXLW
EHIRUHLQVWDOODWLRQ7XUQWKHFLUFXLWEUHDNHUWRWKH2))
position or remove the fuse.
A. Connect the disposer to 110-120 Volt, 60 Hz AC
current only.
B. If a plug-in cord
is used, use
a three prong
plug. Ground
wire should be
attached to the
ground screw in
the bottom of the
disposer (end
bell).
&8VHDFDEOH
clamp strain relief
connector where
power cord enters
the disposer.
To Wire Your Disposer Directly into the House
Current:
GROUNDING INSTRUCTIONS: 7KLVGLVSRVHUPXVW
be connected to a grounded, metal, permanent wiring
system; or an equipment-grounding conductor must
be run with the circuit conductors and connected
to the equipment-grounding terminal or lead on the
appliance.
$,I\RXXVH%;FDEOH
7KHVHSURGXFWVDUHGHVLJQHGIRUKRXVHKROGXVH
2. Connect white wire to white lead of disposer with
a wire nut. Connect black wire to black lead of
disposer with a wire nut. Connect bare ground
ZLUHWRWKHJURXQGVFUHZ7KHJURXQGZLUHVKRXOG
be clamped and held by a strain relief.
'RQRWXVHDULJLGFRQGXLWIRUWKHZLULQJ
connection.
4. A dedicated acceptable motor switch, with the
off position marked, shall be provided for this
GLVSRVHUDWWKHWLPHRILQVWDOODWLRQ7KHVZLWFK
shall be mounted in sight of the disposer or the
sink opening
for the
disposer.
,I%;FDEOHLVQRW
used, provide a
separate ground
wire to nearest
reliable ground,
using the screw in
the end bell for the
ground wire.
B. If your power
supply does not
include a ground wire, you must provide one unless
metal cable is used. Attach a copper wire securely
to disposer ground screw and attach other end of
ZLUHWRDUHOLDEOHJURXQG8VHRQO\8/DSSURYHG
ground clamp. If plastic pipe is used in your home,
a qualified electrician should install a proper ground.
CONNECTING ELECTRICITY (Cont)
READ AND SAVE THESE INSTRUCTIONS
7UDFHOHDGFRQQHFWHG
to this blade and attach
that lead to white wire
on disposer
NOTE: When viewing face of
electrical plug with grounding
pin at top, the larger left blade is
connected to the identified wire.
Ribbed
Side
Strain
Relief
Nut
Heyco Box
Connectors
3DUW1R
Red
Reset
Button
Remove
Bottom Cap
Wire Nuts
Ground Screw
7R+RXVH
Current
RU3RZHU
Cord
%RWWRPRIWKH'LVSRVHUHQGEHOO
Loading ...
Loading ...
Loading ...