Arc Adjustment
(All PGJ adjustable heads are PRESET to
approximately 40°)
1. Rotate the nozzle turret counterclockwise
to the left stop.
2. Now, rotate the nozzle turret clockwise to
the right stop. This is the xed side of the
arc. The nozzle turret must be held in this
position for all arc adjustments.
To increase arc:
1. Insert the key end of the Hunter wrench
into the adjustment socket on top of the
sprinkler.
2. While holding the nozzle turret at the right
stop, turn the wrench clockwise.
3. Wrench will stop turning when adjusted to
the maximum arc (360°). Do not go past
this stop.
4. Adjust to any arc between 40°-360°.
To decrease arc:
1. Insert the key end of the Hunter wrench
into the adjustment socket.
2. While holding the nozzle turret at the right
stop, turn the wrench counterclockwise.
3. Wrench will stop turning when adjusted to
the minimum arc (40°). Do not go past this
stop.
4. Adjust to any arc between 40°-360°.
Radius Adjustment
To decrease radius:
1. Turn nozzle-retainer/range-adjustment
screw clockwise using hex end of Hunter
tool or slot screwdriver. This can reduce
radius up to 25%.
2. If an even smaller radius is desired, install
a smaller nozzle. This will affect precipita-
tion rate.
To increase radius:
1. Turn nozzle-retainer/range-adjustment
screw counterclockwise using hex end of
Hunter tool or slot screwdriver.
2. If larger radius is desired, install larger
nozzle. This will affect precipitation rate.
Precipitation Rate Adjustment
To increase precipitation:
1. Remove existing nozzle.
2. Replace with larger size.
3. Adjust radius.
To decrease precipitation:
1. Remove existing nozzle.
2. Replace with smaller size.
3. Adjust radius.
Note: Undamaged nozzles are reusable.
PGJ
Gear Driven Sprinklers
Hunter Industries Incorporated • The Irrigation Innovators
© 2004 Hunter Industries Incorporated
www.HunterIndustries.com P/N 700974 LIT-379 3/04
Fig. 3
Nozzle/Range
Adjustment
Screw
Lifting
Socket
Adjustment
Socket
Model
Identification
®
Fig.
Radius Reduction Screw
cke
®
PGJ
Nozzle
ID. Tab
Adjustmen
t
Radius Reduction Screw
Plus+
Minus-
Arc Adjustment
Pull-up
Socket
V
M
A
D
E
I
N
U
S
A
Plus+ Minus-- Arc Adjustment
Pull-up
Socket
Nozzle Installation
1. Insert the plastic key end of the Hunter
wrench into the lifting socket of the sprin-
kler and turn 90°. Pull the riser up to gain
access to the nozzle socket.
2. Using the hex key of the Hunter wrench,
turn the radius adjustment screw coun-
terclockwise to be sure it is not blocking
the nozzle socket opening. If a nozzle is
already installed, it can be removed by
backing out the adjustment screw and
turning on the water, or by prying outward
under the nozzle.
3. Slip the desired nozzle into the nozzle
socket. Note that the socket is angled up
Data represented test results in zero wind. Adjust for local conditions. Radius may be reduced up to 25% with adjustment screw (this may alter the uniformity of spray pattern).
Optimum performance is shown in bold type.
For warranty information on Hunter Sprinklers, consult factory.
PGJ
Gear Driven Sprinklers
PGJ Nozzle Performance Data
Pressure Radius Flow Precip in/hr
Nozzle PSI ft. GPM
.75
30
40
50
15'
16'
17'
0.64
0.75
0.85
0.55
0.56
0.57
0.63
0.65
0.65
1.0
30
40
50
18'
19'
19'
0.85
1.0
1.1
0.51
0.53
0.59
0.58
0.62
0.68
1.5
30
40
50
21'
22'
22'
1.3
1.5
1.7
0.57
0.60
0.68
0.66
0.69
0.78
2.0
30
40
50
24'
25'
25'
1.7
2.0
2.3
0.57
0.62
0.71
0.66
0.71
0.82
2.5
30
40
50
27'
28'
28'
2.2
2.5
2.8
0.58
0.61
0.69
0.67
0.71
0.79
3.0
30
40
50
30'
31'
31'
2.5
3.0
3.4
0.53
0.60
0.68
0.62
0.69
0.79
4.0
30
40
50
33'
34'
34'
3.7
4.0
4.3
0.65
0.67
0.72
0.76
0.77
0.83
5.0
30
40
50
36'
37'
37'
4.7
5.0
5.3
0.70
0.70
0.75
0.81
0.81
0.86
Note: All precipitation rates calculated for 180 degree operation.
For the precipitation rate for a 360 degree sprinkler, divide by 2.
PGJ Nozzle Performance Data – Metric
Pressure Radius Flow Precip mm/hr
Nozzle Bars kPa m m
3
/hr l/min
.75
2.1
2.8
3.4
206
275
344
4.6
4.9
5.2
0.15
0.17
0.19
2.4
2.8
3.2
14
14
14
16
17
17
1.0
2.1
2.8
3.4
206
275
344
5.5
5.8
5.8
0.19
0.23
0.25
3.2
3.8
4.2
13
14
15
15
16
17
1.5
2.1
2.8
3.4
206
275
344
6.4
6.7
6.7
0.30
0.34
0.39
4.9
5.7
6.4
14
15
17
17
18
20
2.0
2.1
2.8
3.4
206
275
344
7.3
7.6
7.6
0.39
0.45
0.52
6.4
7.6
8.7
14
16
18
17
18
21
2.5
2.1
2.8
3.4
206
275
344
8.2
8.5
8.5
0.50
0.57
0.64
8.3
9.5
10.6
15
16
18
17
18
20
3.0
2.1
2.8
3.4
206
275
344
9.1
9.4
9.4
0.57
0.68
0.77
9.5
11.4
12.9
14
15
17
16
18
20
4.0
2.1
2.8
3.4
206
275
344
10.1
10.4
10.4
0.84
0.91
0.98
14.0
15.1
16.3
17
17
18
19
20
21
5.0
2.1
2.8
3.4
206
275
344
11.0
11.3
11.3
1.07
1.14
1.20
17.8
18.9
20.1
18
18
19
21
21
22
Note: All precipitation rates calculated for 180 degree operation.
For the precipitation rate of a 360 degree sprinkler, divide by 2.
For more information on precipitation rates see page 105.
25° so that the nozzle range screw threads
directly down. Then tighten the nozzle
range screw. The arrow on the rubber
cover will always indicate the location of
the nozzle and direction of the water ow
when the sprinkler is retracted.
Removing Filter Screen
for Cleaning
Proper Installation
Height
