Documents: Go to download!
User Manual
- Owner's manual - (English, French, Spanish)
- What's in the Box?
- Getting to Know Your HOOVER" SmartWash Pet Complete
- Getting Started With Your SmartWash Carpet Cleaner
- Using Your SmartWash Pet Complete Carpet Cleaner
- Maintenance
- Troubleshooting
Table of contents
USER MANUAL Carpet Cleaner
What's in the Box?
Getting to Know Your HOOVER" SmartWash Pet Complete
- Triggerless Handle Design & Removable Spot Chaser Pretreat Wand
- Clean Water Tank
- Filter
- Dirty Water/Recovery Tank
- Hose Connection
- Removable Recovery Nozzle
- Automatic wash/Dry LED Display
- Removable FlexForce™ PET PowerBrushes
- Solution Tank
- Carry Handle
- Cord Wrap
- Handle Release Pedal
- On/Off Pedal
Getting Started With Your SmartWash Carpet Cleaner
ASSEMBLY
- Slide the handle into the base until you hear a "click".
- Wrap the power cord around the cord hooks for convenient storage
FILL THE CLEAN WATER TANK
- Lift up to remove the clean water tank
- Remove the cap and add warm water to the top of tank. Replace the cap.
-
- Align Clean Water Tank with the body of the cleaner and press FIRMLY into place.
FILL THE SOLUTION TANK
- Remove the solution tank from the back of the cleaner
-
- Remove the cap and fill with HOOVER Cleaning Solution to the top of the tank . Replace cap
-
- Place the Solution Tank back into the cleaner and press FIRMLY into place.
-
Using Your SmartWash Pet Complete Carpet Cleaner
- Unwrap the power cord and plug cleaner in an electrical outlet
- Step on the Handle Release Pedal to recline the cleaner to cleaning position
- Step on the On/Off Pedal to turn ON.
-
- Slowly move forward. The cleaner will automatically dispense the optimal amount of water and cleaning solution.
-
- Slowly pull backward. The cleaner will automatically dry your carpets by extracting the water and cleaning solution.
-
- When you finish cleaning but further drying is required, press the DRY ONLY BUTTON. The Dry Only mode will extract remaining water from your carpet. Continue in this mode until little water is visibly passing through the Nozzle.
-
- For best results, HOOVER® recommends rinsing the carpet with clean water only. This will remove residual carpet cleaning solution from your carpets. To rinse with clean water only, remove the Solution Tank and then repeat steps 4 through 6.
-
Maintenance
How to Empty
- Turn the cleaner off and unplug from electrical outlet
-
- Grab the Dirty Water Tank handle and pull up to release. Remove Tank from carpet cleaner base at an angle.
-
- Place on a flat surface and unlatch Dirty Water Tank lid to remove top of tank.
-
- Empty tank, rinse, wipe filter clean and allow to air dry.
-
How to Remove and Clean Nozzle
- To prevent possible leaking, remove and empty Clean Water Tank, Dirty Water Tank and Solution Tank.
-
- With handle in upright position, lift up on the Nozzle release then pull Nozzle forward to remove from carpet cleaner. CAUTION, pull Nozzle carefully outwards and not upwards.
-
- Rinse debris from Nozzle
-
- Position Nozzle onto foot, making sure to align the tabs at the top of the Nozzle with the notches inside the foot.
-
- Slide Nozzle forward to snap into position
-
Troubleshooting
PROBLEM | POSSIBLE CAUSE | POSSIBLE SOLUTION |
---|---|---|
Cleaner won't run |
|
|
Low suction | 1. Dirty Water Tank full/automatic shut off engaged 2. Blockage in tool on end of hose 3. Dirty Water Lid not on correctly 4. Dirty Water Tank Debris Filter clogged 5. Blockage in Nozzle 6. Dirty Water Tank not properly secured 7. Dirty Water Nozzle not on correctly 8. Blockage in hose |
|
Hose Nozzle stops spraying liquid during use | 1. Clean Water Tank or Detergent Container is empty 2. Loose connection to solution port on foot of cleaner |
|
Accessory Tool will not spray after filling the Clean Water Tank or Solution Tank | 1. Air is trapped in the hose & pump |
|
Hose will not spray after priming pump | 1. Pump is defective 2. Not connected properly |
|
Clean water won’t dispense | 1. Clean Water Tank or Solution Tank not firmly in place 2. Clean Water Tank or Solution Tank empty |
|
Solution won't dispense | 1. Cleaner is not moving in forward direction |
|
Brushes won't rotate during floor cleaning | 1. Brushroll stall protection activated 2. Unit in upright position |
|
Water is leaking out of Carpet Cleaner | 1. Clean Water Tank, Solution Tank or Dirty Water Tank not FIRMLY in place |
|
Spot Chaser Pretreat Wand will not dispense | 1. Batteries installed incorrectly or need to be replaced. Spray will start to lessen as the battery gets close to dead. 2. Spray tip clogged |
|
See other models: BH50020 UH71100 UH71200 WH21000 FH50702