Electronic Inverter Panel with WiFi
Operating Instructions
Model: GPPH710, GPPH720, GPPH730
CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this appliance. Covering this appliance
presents fire risk and will activate the safety fuse; permanently disabling the
unit.
WARNING: Do not use this appliance in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a minimum distance of 1 metre from the air outlet.
General Care and Safety Guide
• Use only the voltage specified on the rating label of the appliance.
• Keep all objects at least 1 metre from the front and 150mm from the sides of
the appliance.
• This appliance is intended for household use only and not for commercial or
industrial use.
• Indoor use only.
• Use this appliance only as described in this manual. Any other use is not
recommended by the manufacturer and may cause fire, electric shock or
injury.
• Do not use the appliance if it has been dropped or damaged.
• The common cause of overheating is deposits of dust or fluff in the appliance.
Ensure these deposits are removed regularly by unplugging the appliance and
vacuum cleaning the air vents and grills.
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.
• Never use the appliance to dry clothes.
• Always unplug appliance when not in use.
• When the appliance has been unpacked, check it for transport damage and
ensure all parts have been delivered. If parts are missing or the appliance has
been damaged, contact the Customer Services Team.
• Do not use if there are visible signs of damage to the appliance.
• Do not connect the appliance to mains supply until completely assembled and
adjusted.
• Ensure hands are dry before handling the plug or main unit.
• Ensure appliance is on a flat, stable, heat-resistant surface.
• Do not operate with cord set coiled up as a heat build up is likely, which could
be sufficient to become a hazard.
• Carry out regular checks of the supply cord to ensure no damage is evident
• Do not operate this appliance with a damaged cord, plug or after the appliance
malfunctions or has been dropped or damaged in any manner. Take to a
qualified electrical person for examination, electrical service or repair.
• Do not twist, kink or wrap the cord around the appliance, as this may cause the
insulation to weaken and split. Always ensure that all cord has been removed
from any cord storage area and is unrolled before use.
• It is recommended that this appliance is plugged directly into the wall socket.
Power boards are not rated to supply power to high wattage appliances.
• A correctly specified, undamaged extension cord may be used with this
appliance provided it is used in a safe manner.
• Do not remove plug from power socket until the appliance has been switched
off.
• Do not remove plug from power socket by pulling cord; always grip plug.
• Do not place cord under carpet or cover with rugs or furniture. Arrange the cord
so it cannot be tripped over.
• Don’t place appliance on bedding or on thick & long carpet where the openings
may get blocked.
• Switch off and use handle provided when moving
• Do not place appliance close to radiant heat source.
• Do not insert or allow foreign objects to enter any ventilation or exhaust
opening, as this may cause an electric shock, fire or damage to the appliance.
• Do not sit on the appliance.
• Do not use abrasive cleaning products on this appliance. Clean with a damp
cloth (not wet) rinsed in hot soapy water only. Always remove plug from the
mains supply before cleaning.
• Do not operate in areas where petrol, paint or other flammable liquids are used
or stored.
• Do not use this appliance in the immediate surrounds of a bath, a shower, or a
swimming pool or other liquids.
General Care and Safety Guide
• The appliance must not be immersed in any liquids.
• There are no user serviceable parts installed in the unit.
• Do not place the unit in wardrobes or other enclosed spaces as this may cause
fire hazards.
• This unit is not supposed to be used in or around locations where foodstuffs,
works of art or delicate articles of science, etc. are stored.
• If your appliance does not work, or is not working properly, contact the place of
purchase or the Customer Services Team.
General Care and Safety Guide
Components
CONTROL PANEL
HEAT OUTLET
AIR INLET
CASTOR WHEELS X 4
CASTOR WHEEL BRACKETS X 2
MAIN POWER SWITCH
WALL MOUNTING
BRACKET
FREE STANDING
1. Ensure the appliance is unplugged and power switches are off.
2. Carefully turn the main body upside-down on a scratch-free and stable surface. Be
careful to prevent damage to the cosmetic finish or your floor surfacing.
3. Align the screw hole on the Castor Wheel Bracket with the screw hole on the base of
the appliance.
4. Attach Castor Wheel Bracket with the ‘1 way screws’ provided and ensure the
bracket sits firmly in place (do not over tighten). Firmly press Castor Wheels into
the slots provided on the Castor Wheel Bracket until they click into place. Some
force may be required.
5. Set appliance upright.
NOTE: The wall bracket edges may be sharp. It is recommended that if using as a free
standing appliance please remove the wall bracket from the back of the heater.
Before using this appliance, it must either be wall mounted or have the castor plates and
castors fitted.
This appliance has been supplied with ‘1 way screws’ for permanent installation of the
feet. This is a safety requirement for the New Zealand and Australian market.
Assembly Instructions
Installation Instructions
The appliance must not be located immediately below a socket outlet.
NOTE: Your Panel Heater should be installed with at least 150mm clearance from the
floor and any other surrounding parts including other appliances and side walls.
At least 300mm clearance from ceilings, shelves and soft furnishings.
Note: Do not run the power cord behind the heater.
WALL MOUNTED HEATERS ARE
ONLY TO BE MOUNTED ON HEAT
RESISTANT WALLS THAT COMPLY
WITH CURRENT AS/NZS
SPECIFICATIONS & BUILDING
REGULATIONS
150mm
300mm
150mm
150mm
WALL MOUNTED
1. Make sure the appliance is unplugged and power switches are off.
2. Position the panel appliance within one metre of a wall socket. Do not mount in front of or
below the wall socket. Ensure there is at least 150mm clearance on all sides of the
appliance.
3. Detach the mounting bracket from the back of the panel appliance by unscrewing the two
locking screws (located on the top of the mounting bracket).
4. Position the mounting bracket on the wall and mark the hole positions with a pen or pencil
and check they are horizontal with a spirit level. Ensure the two bottom mount holes are at
least 150mm from the floor and drill holes as required.
5. Secure the mounting bracket to the wall with the mounting screws. (For masonry walls use
the plastic sheaths).
6. Slot the back of the appliance onto the mounting bracket locating the bottom plugs first
and secure with two locking screws.
7. Plug appliance into a standard 240 volt AC electrical outlet.
Operating Your Heater
Always choose a safe location for the heater, keeping in mind the safety precautions
outlined. Ensure all packaging has been removed from the unit before use. Please
follow the below instructions.
WARNING: In order to avoid overheating or fire, do not cover the heater.
WARNING: Keep all objects at least 1 metre from the front and 150mm
from the sides of the appliance.
WARNING: Do not use this heater with a programmer, separate timer,
remote-control system or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned
incorrectly.
WARNING:Never leave this heater unattended when in use.
If mounted on castors, ensure heater is on a flat, stable, heat-resistant
surface.
Once the heater is in a safe operating position and all switches are in the off
position, insert the power plug into the mains outlet and switch on.
CAUTION: Ensure the power cord is not tight because if pulled it may
partially pull the plug from the socket. A partially inserted plug will overheat
the plug and socket and could result in fire.
Note: When the appliance is turned on for the first time, it may release a
slight odour or smoke. This odour or smoke is a normal occurrence caused by
the initial heating of the heating elements and should not occur again.
1. LED display
2. On/Off button
3. Mode setting button
4. Up button
5. Down button
6. Power setting button
7. Power indicator lights
8. Comfort indicator light
9. Economy indicator light
10. Anti-frost indicator light
11. Timer indicator light
12. Auto indicator light
13. User indicator light
14. WiFi button
8
9
10
4 5
11
1 12
13
7
6
3
2
14
Operating Your Heater
Press the button. A beep will sound indicating the heater is now on and the setting will be
“AUTO” mode. The current temperature will be displayed on the screen.
To turn the heater off, press the button for at least 2 seconds until the heater switches off.
AUTO Mode
In “AUTO” mode you can set either Comfort or Economy settings as shown below. The default
temperature setting is 25
o
C. Set your desired temperature by pressing the UP or DOWN
buttons. The screen will return to the current temperature after a few seconds but the set
temperature will be retained unless changed by you.
Comfort mode can be set from 5 – 35
o
C
Economy mode can be set from 5 - 31
o
C (this is pre-set so there is always a 4
o
C
difference between Comfort and Economy settings)
You may want to set the economy temperature to a much lower level than the comfort
temperature and set the heater to economy when going to bed so that the room it is in stays
warm but not as hot as you would have it if you were in the room.
The heater will automatically set the best heat setting to reach the temperature you have set
and will adjust the heat setting to maintain the temperature you have set. The blue lights will
show which heat setting is currently in use.
USER mode
Press the button to change from AUTO to USER mode. The power setting will go to high (all
blue lights illuminated). You can select the power setting you want. There are 5 levels. The blue
lights will decrease with each push. When it reaches the bottom light (lowest heat setting) the
heater will then go back into AUTO mode.
In “USER” mode you can set either Comfort or Economy settings as shown below. The default
temperature setting is 25
o
C. Set your desired temperature by pressing the UP or DOWN
buttons. The screen will return to the current temperature after a few seconds but the set
temperature will be retained unless changed by you.
Comfort mode can be set from 5 – 35
o
C
Economy mode can be set from 5 - 31
o
C (this is pre-set so there is always a 4
o
C
difference between Comfort and Economy settings)
You may want to set the economy temperature to a much lower level than the comfort
temperature and set the heater to economy when going to bed so that the room it is in stays
warm but not as hot as you would have it if you were in the room.
Check that the heater main power switch is in the OFF position before plugging into the mains
supply.
Turn the main power switch which is on the right hand side of the appliance just below the
control panel to the “I” position to turn the heater on. The heater will beep once and will be
stand by mode.
Operating Your Heater
You can set the heat setting to any of the 5 levels to heat the room. It is best to set it at the
highest setting to initially heat up the room and then set to a lower level to maintain the setting.
When the room reaches the set temperature, the element will turn off and not turn on again
until the room temperature drops lower than the set temperature.
ANTI-FROST mode.
The heater is fitted with an “anti-frost” mode which can be activated by pressing the MODE
button until the symbol is illuminated. The heater will automatically come on if the
temperature drops below 5 degrees. Note the appliance has to be turned on for this function to
work. To deactivate this mode press the MODE button again to go back to comfort or economy
mode.
AUTO OFF TIMER
Set the timing function by pressing the button twice in quick succession.
The TIMER symbol will light and the screen starts flashing, use the UP or DOWN
buttons to set the desired turn off time (from 1 to 24 hours). Once the set time has elapsed the
heater will turn off.
CHILD LOCK
To activate the child lock, press both the UP and DOWN buttons together for 3 seconds and the
heater will then display [ ] to show the lock is active. After 5 seconds the screen will return to
showing the heater settings but none of the keys will work until the child lock is deactivated by
pressing both the UP and DOWN buttons again for 3 seconds.
Operating Your Heater
WiFi – Downloading and Setting up APP
For WiFi, the APP is supported only on 2.4GHz WiFi channels.
Please ensure your phone is 2.4GHz capable.
Read and agree to the Privacy Policy.
Tap REGISTER in the centre of the screen.
If you already have an existing account, then you
can Log In.
Download Goldair mobile APP
• Open the APP Store or Google Play on your
mobile phone.
• Open 'Search' and enter 'Goldair'
• Click 'GET' and begin to download and install.
Once downloaded to your phone open the APP
WiFi – Downloading and Setting up APP
You need to register an email address.
Enter you email address then press 'Get authentication code'.
Pairing APP to Fan
Enter the verification code that you will receive by email
Next you will be prompted to Set a Password. The password must contain 6 - 20 characters and must be a
mix of letters and numbers.
Pairing APP to Heater
On your phone tap the ‘+’ to connect to the heater.
Tap ‘Confirm indicator rapidly blink’ on the phone.
Press the “WiFi” button on the control panel of the
heater for 5 seconds until the WiFi indicator light
starts flashing.
WiFi Set
Button
Pairing APP to Heater
When the phone interface shows the addition is
successful, and the WIFI indicator on the heater
will stop flashing.
The heater pairing is complete and the main
control screen on your phone will appear showing
the heater as ON.
If the phone and heater fail to connect, then you will need to try to connect again as per the above
process.
Choose/confirm which WiFi to connect to.
Note: your phone may pick up other WiFi signals
(e.g. neighbours) so you will need to choose.
Enter your WiFi password and press ‘Confirm’
The phone will then connect to the heater.
Ensure you have a good strong signal from your
WiFi router.
Note: The WiFi indicator on the heater may go off
during this pairing process.
Once complete the screen showing the device has
been successfully added will appear.
Rename the heater if desired.
Tap “Done” to continue.
Operating your Heater from the APP
You can rename the heater.
Tap the 3 dots on the top right of the control
screen of the APP to take you to the next page.
Click “Modify Device Name” and rename the
heater. Example: Bedroom 1, Dining Room etc. and
tap save.
DEVICE SHARING SET UP
The person you add will need to have the Goldair Heater APP installed on
their phone.
Open the “GOLDAIR APP” and tap the 3 dots in the top right of the
screen.
Tap "Add Sharing" to enter the number of the person you want to
include or tap the phone icon to select the persons phone number.
Tap “Confirm” to complete the addition.
DEVICE SHARING CANCELLATION
Open the “GOLDAIR APP” and tap the 3 dots in the top right of the
screen. Tap “Add Sharing” and delete the phone numbers of shared
members to cancel the device sharing.
NOTE: There can only be one user operating the heater at a time. The
APP needs to be closed on all other devices to enable the sharing to
work.
NOTE: If someone else sets up their phone on the same heater without
using the “Device Sharing” the original phone will be disconnected and
the heater will disappear from the device list.
Operating your Heater from the APP
Mobile phone remote operation (connect heater
power and turn on the side switch, so that the
heater is in standby mode).
Open the “GOLDAIR" APP to select the heater
(when using one mobile phone to control multiple
heaters, you need to select the heater to be
operated).
• Select the heater to be operated and enter the
operation interface.
If the phone interface color is dark red, this
indicates that the heater is in the OFF standby
setting.
• Tap the OFF icon and the heater will turn on.
The display will change to bright red.
• You can now control the heater.
• To turn the heater off again tap the power icon
and the heater will revert to the dark screen.
TEMPERATURE SETTING:
• Tap the "+" or "-" button to set the
temperature.
• When the set temperature is higher than the
ambient temperature, the heater begins to
heat.
• If the heater temperature setting is below
ambient temperature the heater will be in
standby mode and will not operate until the
ambient temperature drops below the set
temperature.
Depending on which mode you are in you can set
the temperature as below.
Comfort mode can be set from 5 – 35
o
C
Economy mode can be set from 5 - 31
o
C
(this is pre-set so there is always a 4
o
C difference
between Comfort and Economy settings)
LED Display Icon
Tap this icon to turn off the LED display on the
heater. This does not affect the operation of the
heater.
To turn the heater display back on, tap the icon
again
Dark Red – Heater Off
Bright Red – Heater On
MODE
Mode can be set to Comfort, Eco or Anti-frost.
Set your desired temperature in Comfort or Eco
modes by pressing "+" or "-" buttons.
The screen will display which mode has been
selected and the current set temperature and
ambient temperature.
Comfort mode can be set from 5 – 35
o
C
Economy mode can be set from 5 - 31
o
C
(this is pre-set so there is always a 4
o
C difference
between Comfort and Economy settings)
Anti-frost mode is pre-set at 5
o
C and cannot be
adjusted.
HEAT SETTINGS
In USER, you can set the heat settings from ONE
(lowest) to FIVE (highest) and the set level will be
shown on the bottom of the APP.
It will also show on the heater display.
In AUTO, the heater will adjust the heat settings
automatically to suit the amount of power
required to reach and then maintain the set
temperature.
CHILD LOCK
Tap the padlock icon to display the closed padlock
and “ON”, indicating that the child lock is active.
Tap the padlock icon again to unlock the child lock.
You can adjust the heater settings with your mobile
phone without having to unlock the child lock.
If you want to adjust the heater using the heater
controls then you must first press the heaters press
both the UP and DOWN buttons
together for 3 seconds or tap the padlock button
on the APP to unlock it.
Operating your Heater from the APP
AUTO OFF TIMER
When the heater is ON you can set it to turn OFF
after a number of hours (1-24 hours) has elapsed.
• In the APP, tap the heater to be operated and
enter the operation interface.
• With the power icon on the lower left corner of
the mobile phone interface is displaying ON
and the heater is turned ON.
• Tap the timer button and scroll to select the
number of hours before the heater will turn
OFF and tap OK to return to the heater
operation interface.
• The timer icon on the lower right will display
how long before the timer will turn the heater
OFF.
To cancel the timer, touch the timer button again
and the numbers will disappear and just show
timer.
SUPPORT AND TECHNICAL ADVICE
Goldair – New Zealand
Monday – Friday 8am-5pm
Phone +64 (0)9 917 4000
Phone 0800 232 633
Goldair – Australia
Monday – Friday 8am-5pm
Phone +61 (0)3 9365 5100
Phone 1300 465 324
Operating Your Heater
PROOF OF PURCHASE
To receive warranty retain receipt as proof of purchase.
TECHNICAL SPECIFICATION
Model No: GPPH710 GPPH720 GPPH730
Supply: 220-240VAC 50Hz 220-240VAC 50Hz 220-240VAC 50Hz
Wattage: 900-1000W 1350-1500W 1800-2000W
SAFETY DEVICES
This appliance has three protection devices:
• Tilt Switch - this will automatically turn the appliance off if the appliance is not in
the correct operating position.
• Resettable Thermal Link - this will automatically disconnect the power to the
appliance at a pre-set overheat temperature. After cooling down it will reset and
power on again. If this occurs, investigate what is causing the appliance to
overheat.
• Thermal Fuse - this disconnects the appliance permanently in case of overheating.
(It is non resettable).
CAUTION: The appliance generates heat during use. Precautions must be
taken to prevent the risk of burns, scalds, fires or other damage to persons.
CARE AND CLEANING
The heater requires regular cleaning to ensure trouble free operation:
• Unplug the heater from the mains supply before cleaning.
• Ensure that the heater has been allowed to cool down completely before cleaning.
• The common cause of overheating is deposits of dust or fluff in the appliance.
Ensure these deposits are removed regularly by unplugging the appliance and
vacuum cleaning the air vents and grills.
• Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and
dirt.
• Never use solutions such as petrol, thinners or polishing agents.
• Ensure the heater is dry before plugging back into the mains supply.
• Do not attempt to dismantle the heater.
• There are no user serviceable parts. For service or repair, contact an authorised
electrical service technician.
Thank you for purchasing this Goldair Platinum product. Your product is warranted against faults and manufacture when used in
normal domestic use for a period of three years. In non-domestic use Goldair limits the voluntary warranty to three months.
Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the
warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone
other than a qualified electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the
goods or services to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).
Three Year Warranty
Goldair Three Year Warranty (IMPORTANT: Please complete and retain this warranty card)
Name
Address
Place Of Purchase Date Of Purchase
Name Of Product Model Number
Attach a copy of the purchase receipt to this warranty card
Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.
Goldair – New Zealand
CDB Goldair
PO Box 100-707
N.S.M.C
Auckland
Phone +64 (0)9 917 4000
Phone 0800 232 633
www.goldair.co.nz
Goldair – Australia
CDB Goldair Australia Pty
PO Box 574
South Morang
Victoria, 3752
Phone +61 (0)3 9365 5100
Phone 1300 GOLDAIR (1300 465 324)
www.goldair.com.au
New Zealand
PO Box 100707,
North Shore Mail Centre,
Auckland, 0745
www.goldair.co.nz
Australia
PO Box 574,
South Morang,
Victoria, 3752
www.goldair.com.au
