Candy CBG620X Hoods

User Manual - Page 2

For CBG620X.

PDF File Manual, 8 pages, Read Online | Download pdf file

CBG620X photo
Loading ...
ENGLISH
INSTALLATION
The appliance can be used in both the filtering and ducting version. In the Filtering version (Fig. 4), the
air and vapours conveyed by the appliance are depurated by charcoal filters and recirculated around the room.
ATTENTION: When using the filtering version, charcoal filters must be installed (the charcoal filters are not supplied).
In the Ducting version (Fig. 3), cooking vapours and odours are conveyed straight outside by a disposal duct
which passes through the wall. Use of charcoal filters is therefore unnecessary.
The following operations are essential for assembly: – Cut a hole in the bottom of the pensile cupboard
in order to settle the appliance (Fig.1). – Set the power supply near the appliance. – Prepare the air venting hole
if your appliance is to be installed in the ducting version.
To install the appliance, adjust the position of the clasping side springs by means of the proper screws (Fig.
2), according to the thickness of the bored panel to which it is going to be anchored.
Insert the appliance in the pensile cupboard and lock it by means of the side springs. Use the holes which
have already been made in the casing of the appliance to definitively fix it by means of additional screws.
Ducting version : connect the disposal duct to the air evacuation pipe of the hood. Use a flexible pipe and
lock it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make
the electrical connections.
Filtering version : connect an adequate pipe to the connecting flange of the appliance so that it conveys
the air up to the top of the pensile cupboard (pipe is not provided). Make the electrical connections.
OPERATION
Controls (Fig. 8):
A = LIGHT switch.
B = MOTOR switch. Position 0: motor off. Position 1: motor on Ist speed. Position 2: motor on 2nd speed. Position
3: motor on 3rd speed.
C = Operating motor warning light.
To gain access to the interior of the appliance remove the metal grille by slidying the two side stops towards
the center (Fig.5).
Grease filters: depending on the versions, the hood features different types of grease filters:
Metal filter (Fig. 7A): this filter is made of metal and is located inside the metal grid; depending on the hood model
purchased by you, two or just one metal filter can be fitted. The filter/s must be periodically cleaned, according
to use, but on average every two months. Wash the filter/s with neutral detergent.
To remove the filter, remove the metal grid by sliding the two side stops towards the centre (Fig. 5); afterwards,
remove the two metal filter stops (F) and take out the filter.
Synthetic filter (Fig. 7B): this filter is made of white synthetic fibre and is located inside the metal grid; it cannot
be washed, but should be periodically replaced according to use (at least every two months).
To remove the filter, remove the metal grid by sliding the two side stops towards the centre (Fig. 5); afterwards,
remove the two metal filter stops (M) and take out the filter.
When using the filtering version of the appliance, the charcoal filters must be changed according to use (Fig.6),
usually every six months. Remove the filters rotating them and replace them rotating into the opposite direction.
To gain access to the light bulbs, remove the grille (Fig. 5) and unscrew the bulbs. Use Only CANDLE HALOGEN
LAMP - Ø 35mm, E14–220-240 Vac, 28W or INCANDESCENT LAMP-E14–220-240 Vac, 40W
DEUTSCH
INSTALLATION
Das Gerät kann sowohl im Umluftbetrieb, als auch im Abluftbetrieb eingesetzt werden. Im Umluftbetrieb (Abb.4)
wird die Luft zusätzlich durch den (einmotoriges Gerät) / die (zweimotoriges Gerät) Kohlefilter geleitet und in den
Raum zurückgeführt. Pro Motor ist somit ein Kohlefilter erforderlich (Die Kohlefilter werden nicht mitgeliefert). Im
Abluftbetrieb wird der Kochdunst durch Abluftrohre ins Freie geleitet (Abb. 3). Kohlefilter sind im Abluftbetrieb
nicht erforderlich.
Auschnitt im Hängeschrank: Im Boden des Hängeschrankes ist ein Ausschnitt anzubringen, der dem
einzusetzenden Gerät entspricht (Abb. 1).
Justierung der Montagehilfe: Die seitlich am Gerät angebrachten Federn dienen als Montagehilfe, die das Gerät
im Ausschnitt des Hängeschrankes festhalten. Um einen einwandfreien Sitz des Geräts zu gewährleisten, müssen
diese Federn auf die Stärke der Platte, in der sich der Ausschnitt befindet, eingestellt werden. Dies geschieht
durch Drehen der entsprechenden Einstellschrauben (Abb. 2).
Einsetzen des Geräts: Das Gerät wird nun von unten in den Ausschnitt des Hängeschrankes eingeführt und
rastet mit den Montagehilfen ein. Nun wird das Gerät von innen her mit der Spanplatte, in der sich der Ausschnitt
befindet, verschraubt. Hierfür befinden sich in dem Gerätegehäuse umlaufend entsprechende Bohrlöcher. Um diese
Loading ...
Loading ...
Loading ...