Loading ...
Loading ...
Rev. C 5/13
10
5165ES
Rev. C 5/13
3
5165ES
MODEL 5165
OSCILLATE
OSCILLATE
Figure 2
Timer Function in Low Heat
OPERATION
1. Carefully remove the Heater from the bag and the carton.
2. Place the Heater on a firm, level surface.
Plastic or rubber tabs, like the feet on this unit, may stick to
furniture surfaces and/or hardwood floors. The unit may leave a
residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces,
and/or hardwood floors.
3. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle
with only the slight movement of the attached cord.
Receptacles in this condition may overheat and pose
a serious fire hazard; if covered by a curtain or drape,
the fire hazard is even greater.
4. When the Heater is initially plugged in, there will be a “beep”
and the Power Light will come on indicating that there is power
to the unit. The Power Light will remain lit until the Heater is
unplugged from the electrical outlet.
5. Turn the Heater ON by pressing the Power Button ( ).
6. Press the ( ) and
( ) buttons at the same time to change the
display to ° Celsius. Press the same two buttons together again
to change the display back to ° Fahrenheit.
7. Upon turning the Heater on, the unit will be in HIGH heat (1500
Watts) (Figure 1).
8. Press the ( ) button for LOW heat.
9. To turn the Heater OFF, press the Power Button ( ) and unplug
the Heater from the electrical outlet.
OSCILLATE
Figure 3
Display reflects High Heat and
Automatic Temperature Control Function
AUTOMATIC TEMPERATURE CONTROL (Figure 3)
The automatic temperature function will only operate on "High"
heat. You cannot set the temperature automatically when the
unit is in the low heat mode.
1. To set the room at a specific temperature press the ( ) or
( )
buttons to the desired temperature. The display will now reflect
the ( ) and the temperature will be flashing. The Heater is now
in Auto Temperature Mode.
2. When you reach the temperature at which you want to set the
unit, the set temperature will flash several times and then the
display will return to indicate the current room temperature and
will gradually change as the room temperature changes. NOTE:
the temperature display does not indicate the temperature of
the heated air being emitted by the heater.
3. Once the room temperature reaches 2 degrees above the set
temperature, the Heater will shut off. Once the room tempera-
ture reaches 1 degree below the set temperature, the Heater
will turn back on and continue to cycle off and on to maintain
the set temperature.
4. This function will cancel if the ( ) button is pressed. The Heater
will now be in High heat and run continuously.
NOTE: It is normal for the Heater “fan” to run for approximately 15
seconds when the Heater shuts off after reaching the set
temperature.
OSCILLATION:
Pressing the Oscillate Button will allow the Heater to oscillate
back and forth. To stop the oscillation, press the Oscillate Button
again. When the Heater is in Automatic Temperature Control, the
oscillation function will stop when the set temperature is reached
and resume when the Heater turns back on.
Figure 1
Display when initially turned on
TIMER FUNCTION:
The timer function may be activated when the Heater display is in
any function or speed. (Figure 2) This function allows you to set
the length of time the Heater will run before turning itself off, from
1 hour to 8 hours. Pressing the Timer Button ( ) will increase the
length of time by 1 hour each time this button is pressed. After the
display reflects 8 hours, pressing the Timer Button ( ) once more
will reset the Heater to run continuously. The Heater will turn off
when the set time has elapsed. The unit can be turned back on by
pressing the Power Button ( ).
MODELO 5165
Vista de frente del
Control Remoto
Si usted pierde su mando a distancia, por favor Cliente de llamada Serive para ordenar un reaplacement en 1-800 -233-0268,
de lunes a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos).
Vista posterior del
Control Remoto
Figura 4
CONTROL REMOTO:
Todas las funciones ejecutadas con el Control Remoto funcionan idénticamente a los controles manuales.(Figura 4)
1. Instale las dos baterías “AAA” (no incluidas).
2. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (níquel-cadmio).
3. NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS PUEDEN ESTALLAR O PUEDEN SALIRSE.
Retire el tornillo
antes de la
instalación de las
baterías
Loading ...
Loading ...
Loading ...