Loading ...
Loading ...
Loading ...
OPERATING INSTRUCTIONS
Resetting the Manual Power Reset Limit Control
Warranty
How to operate your heater
The room temperature is controlled by a line voltage
thermostat located either on the wall, or at the lower
left on the heater (See Page 1; Built-in Thermostat).
1. Once installation is complete and power has been
restored, turn the thermostat knob fully clockwise.
2. When the room reaches your comfort level, turn
the thermostat knob counterclockwise until the heater
turns off. The heater will automatically cycle around
this preset temperature.
3. To reduce the room temperature, turn the knob
counterclockwise. To increase the room temperature,
turn the knob clockwise.
Over Temperature-Limiting Controls
If normal operating temperatures are exceeded (due to abnormal cir-
cumstances), the heater has two temperature-limiting controls (for Model
CST, four controls are used). Both limiting controls are located on the
element assembly. The rst is a manual power reset limit control, de-
signed to open the heater circuit when excessive operating temperatures
are detected and stop the electrical current ow. The problem must be
assessed and the limit must be reset to resume operation.
Further protection is provided by a secondary over-temperature fuse,
which will open the heater circuit in severe over-temperature conditions,
or in the event of component failure. If this occurs, the heater must be
repaired or replaced.
If the manual power reset limit has opened the heater circuit due to excessive operating temperatures, the heater will not
work until it is reset. This can be done at the thermostat or the circuit breaker controlling the heater.
1. Lower the temperature on the thermostat below room tempera-
ture.
2. Allow the unit to cool for at least 20 minutes.
3. Resolve the problem causing the limit to trip (typically the heat-
er is blocked or needs cleaning, see Maintenance Instructions).
4. Raise the temperature on the thermostat back above room
temperature. The heater should come back on. If it does not
come back on, reset heater at the main disconnect panel, using
directions to the right. An additional 20 minute waiting period is
required every time the power is turned off. Restoring power, even
briey, will heat the limit even though the heater does not come
on.
5. The heater is now functional and the thermostat can be reset to
your comfort level.
1. Trip the circuit breaker by switching it to the OFF position.
2. Allow the unit to cool for at least 20 minutes.
3. Resolve the problem causing the limit to trip (typically the heat-
er is blocked or needs cleaning, see Maintenance Instructions).
4. Restore power to the heater by switching the circuit breaker to
the ON position.
5. Raise the temperature on the thermostat above room tempera-
ture. The heater should come back on. An additional 20 minute
waiting period is required every time the power is turned off.
Restoring power, even briey, will heat the limit even though the
heater does not come on.
6. The heater is now functional and the thermostat can be reset
to your comfort level.
Note that resetting the manual power reset limit control may not restore heater operation if a severe over-temperature
condition has occurred. See the Troubleshooting Chart on next page for more information.
To Reset Heater at the Thermostat
To Reset Heater at the Circuit Breaker (recommended
if room temperature is below 45
°
)
For more effective and safer operation and to prolong the life of the
heater, read the Owner’s Guide and follow the maintenance instruc-
tions. Failure to properly maintain the heater will void any warranty
and may cause the heater to function improperly. Warranties are non
transferable and apply to original consumer only. Warranty terms are
set out below.
LIMITED TWO-YEAR WARRANTY: Cadet will repair or replace any
Com-Pak (CS), Com-Pak Twin (CST) heater found to be defective
within two years after the date of purchase.
These warranties do not apply:
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance,
misuse, abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet;
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of
Cadet.
6. The use of unauthorized accessories or unauthorized components
constitutes an alteration and voids all warranties. Refer to Cadet
website or call customer service at 855.CADET.US for list of autho-
rized accessories and components.
7. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACE-
MENT AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR
DAMAGES SUCH AS PROPERTY DAMAGE OR FOR CONSE-
QUENTIAL DAMAGES AND/OR INCIDENTAL EXPENSES RESULT-
ING FROM BREACH OF THESE WRITTEN WARRANTIES OR ANY
EXPRESS OR IMPLIED WARRANTY.
8. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF
YOUR CADET PRODUCT, THE REPLACEMENT PARTS ARE
SUBJECT TO THE SAME WARRANTIES AS THE PRODUCT. THE
INSTALLATION OF REPLACEMENT PARTS DOES NOT MODIFY
OR EXTEND THE UNDERLYING WARRANTIES. REPLACEMENT
OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT
CREATE ANY NEW WARRANTIES.
9. These warranties give you specic legal rights, and you may also
have other rights which vary from state to state. Cadet neither as-
sumes, nor authorizes anyone to assume for it, any other obligation
or liability in connection with its products other than as set out herein.
If you believe your Cadet product is defective, please contact Cadet
Manufacturing Co. at 855.CADET.US, during the warranty period,
for instructions on how to have the repair or replacement processed.
Warranty claims made after the warranty period has expired will be
denied. Products returned without authorization will be refused.
Parts and Service
Visit cadetheat.com/parts-service for information on where to obtain
parts and service.
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials. You
can reduce your carbon footprint by recycling this product
at the end of its useful life. Contact your local recycling
support center for further recycling instructions.
WARNING Risk of Electrical Shock and Fire.
The heater must be properly installed before it is
used.
1. Do not operate without grill.
2. Keep electrical cords, drapery, furnishings and
other combustibles at least 3 feet away from the
front of the heater and 6 inches away from the
sides.
3. Do not tamper with the over temperature limit
control.
4. If the heater over temperature limits trip more
than once per day, the heater must be replaced.
5. Clean heater at least every six months.
6. After allowing the heater to cool, turn power off
at circuit breaker panel before removing grill.
7. Use a hair dryer or vacuum on blow cycle to
blow debris through the top element (do not touch
element).
8. Install the grill before turning on power.
WARNING: Any other service not detailed in
this Owner’s Guide should be performed by an
authorized service representative.
Page 5
Loading ...
Loading ...
Loading ...