Whynter BWR-308SB 15 inch Built-In 33 Bottle Undercounter Stainless Steel Wine Refrigerator

User Manual - Transcript

• Page 1 - English - : BWR208SB BWR308SB BWR208SB 12quot 20 bottles BWR308SB 15quot 33 bottles Whynter 1215 inch BuiltIn 2033 Bottle Undercounter Stainless Steel Wine Refrigerator with Reversible Door Digital Control Lock and Carbon Filter
• Page 2 - English - : Table of Contents PAGE Safety Precautions 3 4 Parts Product Features Installation 7 9 Operation and Controls 10 11 Care and Maintenance Troubleshooting 15 16 Warranty Information Storage 12 13
• Page 3 - English - : Safety Precautions APPLIANCE SAFETY Your safety and the safety of others are very important to us To reduce the risk of fire electrical shock or injury when using your appliance follow these basic precautions WARNING CAUTION Danger means that failure to heed this safety statement may result in severe injury or death Warning means that failure to heed this safety statement may result in extensive product damage serious injury or death Caut ion means that failure to heed this safety statement may result in minor or moderate injury or property or equipment damage All safety messages will alert you to know what the potential hazard is tell you how to reduce the chance of injury and let you know what can happen if the instructions are not followed IMPORTANT SAFETY GUIDELINE Before the appliance is used it must be properly positioned and installed as described in this manual please read the manual carefully To reduce the risk of fire electrical shock or injury when using the appliance follow basic precaution including the following Plug into a grounded 3prong outlet do not remove grounding prong do not use an adapter and do not use an extension cord Do not use if the power supply cord is damaged If damaged it must be replaced by a qualified electrician It is recommended that a separate circuit serving only your appliance be provided Use receptacles that cannot be turned off by a switch or pull chain Never clean appliance parts with flammable fluids or harsh chemicals These fumes can create a fire hazard or explosion Do not store flammable materials or liquids near the appliance Before proceeding with cleaning and maintenance operations make sure to unplug the appliance Do not connect or disconnect the electric plug with wet hands Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician This is the Safety Alert Symbol This symbol alerts you to potential hazards that may serious injury All safety messages will follow the Safety Alert Symbol and either the word quotDANGERquot or quotWARNINGquot
• Page 4 - English - : Safety Precautions Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician This appliance is CFC and HFCfree and contains small quantities of Isobutane R600a which is environmentally friendly but flammable It does not damage the ozone layer nor does it increase the greenhouse effect Care must be taken during transportation and setting up of the appliance that no parts of the cooling system are damaged Leaking coolant can ignite and may damage the eyes In the event of leakage Avoid open flames and anything which creates a spark Disconnect from the mains Air the room in which the appliance is located for several minutes and contact the Service Department for advice FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL Use two or more people to move and install the appliance Failure to do so can result in injury To ensure proper ventilation for your appliance the front of the appliance must be completely unobstructed Choose a wellventilated area with temperatures above 60F 16C and below 90F 32C This appliance must be installed in an area protected from the elements such as wind rain water spray or drips The appliance should not be located next to ovens grills or other sources of high heat The appliance must be installed with all electrical connections in accordance with state and local codes The fuse or circuit breaker size should be 15 amperes It is important for the appliance to be leveled in order to work properly For a stable installation make sure the appliance is placed on a flat level and solid surface Ensure that the surface on which the appliance is placed is strong enough to hold the appliance and the items stored inside Do not use solventbased cleaning agents of abrasives on the interior These cleaners may damage or discolor the interior Keep fingers out of the pinch point areas Clearance between the door and cabinet are relatively small Be careful closing the door when children are in the area This wine refrigerator is designed to store wine bottles If food is stored inside ensure that there is sufficient airflow between items Please note that the temperature range for this wine refrigerator is optimized for wine storage Perishable food items may require a different storage environment and is not recommended Do not place hot food or beverages into the appliance Close the wine refrigerator door immediately after placing items inside to keep the internal temperature relatively constant Avoid placing any objects on top of the appliance This is an electrical appliance to avoid injury from electrical shock do not operate the unit with wet hands while standing on a wet surface or while standing in water Do not use outdoors or in wet conditions When positioning or moving the appliance ensure that it is not turned upside down or unleveled greater than 45 If the appliance does not remain in an upright position allow it to sit upright for a minimum of 4 hours to allow the refrigerant to settle Never pull the power cord to disconnect it from the outlet Grasp the plug and pull it from the outlet Never lift carry or drag the appliance by the power cord This appliance is designed for household noncommercial use only Any other use will void the warranty Do not plug into the power outlet before set up is completed Do not move this appliance without emptying it and securing the door in a closed position
• Page 5 - English - : Parts Keys B W R 8SB BWR308SB 1 Control Panel Temperature Control Light 5 Front Vent 2 Top Hinge 6 Stainless Steel Door 9 Adjustable Legs 3 Shelves 6 7 Handle 10 Interior Light 4 Door Gasket 8 Cylinder lock 11 Keys 12 Drip Tray Rear BWR208SB 4 small legs BWR308SB 2 small front legs 2 big rear legs 13 Activated Carbon Filter inside cabinet
• Page 6 - English - : Our Whynter BuiltIn UnderCounter Stainless Steel Wine Refrigerators offer premium quality and innovative design ideal for your wine collecting needs Whether for the enthusiast or the connoisseur these single zone compressor wine refrigerators provide premium and advanced wine storage functionality The Whynter BWR208SB and BWR308SB can hold up to 20 and 33 standard 750ml wine bottles respectively The powerful compressor cooling process offers optimum temperatures low 40ºF to mid 60ºF for red white and sparkling wines The front ventilation design of these units allow for flush with cabinet installation or simply freestanding usage The premium appeal of these wine refrigerators feature a substantial stainless steel trimmed door accented with a luxurious curved handlebar Designed with intuitive use in mind these refrigerators come equipped with a sleek touch screen control that lets you set the temperature to anywhere from 40ºF 65ºF 5ºC 18ºC TECHNICAL DATA BWR208SB 20 bottles 115V 60Hz 80W 09A 40F 65F 71 lbs 79 lbs 116quot W x 225quot D x 34quot H 141quot W x 265quot D x 375quot H R600a Model Capacity Voltage Power Consumption Temperature Range Net Weight Gross Weight Unit Dimension Packaging Dimension Refrigerant BWR308SB 33 bottles 115V 60Hz 80W 09A 40F 65F 79 lbs 90 lbs 148quot W x 225quot D x 34quot H 1890quot W x 2716quot D x 3975quot H R600a Capacity BWR208SB 20 standard 750ml wine bottles BWR308SB 33 standard 750ml wine bottles Builtin or Freestanding installation Stainless steel glass door with sleek black cabinet Touch screen control with temperature range from 40F 65F Environmentally friendly refrigerant Activated Carbon filter eliminates odors Luxurious curved handlebar Tempered doublepane glass Soft interior LED lighting with onoff switch Internal fanforced circulation for even temperature distribution throughout the cabinet Reversible door swing Fahrenheit and Celsius degree optional temperature indicators 6 removable pullout sliding shelves Cylinder lock and two keys Product Features FEATURES
• Page 7 - English - : Installation IMPORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE Remove the exterior and interior packing Before connecting the appliance to the power source let it stand upright for approximately 4 hours This will reduce the possibility of a malfunction in the cooling system from handling during transportation Clean the interior surface with lukewarm water using a soft cloth Install the handle on the door INSTALLATION OF YOUR APPLIANCE The appliance is designed for builtin recessed or free standing installation WARNING Do not store or install the appliance outdoors CAUTION This wine refrigerator is designed for storing and cooling beverages Do not store perishable food medicine or other medical products Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded We do not recommend installing the appliance on carpet To level your appliance adjust the leveling legs at the bottom of the appliance if needed For free standing installation 5 inches 127mm of space between the back and sides of the appliance is suggested which allows the proper air circulation to cool the compressor and condenser Even for builtin installation a ¼ 635mm space is required on each side and at the top The front air vent must never be covered or blocked in any way NOTE DO NOT install the appliance near an oven or other heating source Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption For best performance do not install the appliance behind a cabinet door or block the base grille Avoid locating the appliance in area that may be exposed to excessive moisture Plug in the appliance into an exclusive grounded wall power outlet Do not under any circumstances cut or remove the third ground prong from the power cord Any questions concerning power andor grounding should be directed toward a qualified electrician or contact Whynter Customer Support WARNING To reduce the risk of fire electrical shock or injury when using your appliance follow these basic precautions Read all instructions before using the appliance DANGER or WARNING An empty wine refrigerator can be a hazardous for children or small pets If disposing of the wine refrigerator remove gasket seals latches lids or the entire door from your unused appliance or take other action to ensure the wine refrigerator is harmless Never allow children to operate play with or crawl inside the appliance Never clean appliance parts with flammable fluids or harsh chemicals The fumes can create a fire hazard or explosion Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance The fumes can create a fire hazard or explosion
• Page 8 - English - : Installation BUILTIN CABINET INSTRUCTIONS These appliances are designed for both builtin or free standing installation For builtin installation ensure proper service access and ventilation allow at least ¼ space on each side and at the top CABINET OPENING DIMENSIONS minimum Width 1185 Depth 2275 Height 3425quot BWR208SB BWR308SB 1505quot 2275quot 3425quot ELECTRICAL CONNECTION WARNING Improper use of the grounded plug can result in the risk of electrical shock If the power cord is damaged have it replaced by a qualified electrician or contact Whynter Service Department Gasket a This appliance requires a standard 115120 Volt AC 60Hz electrical ground outlet with threeprong Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance This provides the best performance and also prevents overloading the house wiring circuit that could cause a fire hazard from overheating Never unplug the appliance by pulling the power cord Always grip the plug firmly and pull straight out from the receptacle Repair or replace the power cord immediately if it becomes frayed or otherwise damaged Do not use a cord that shows cracks or abrasion damage along its length or at either end When moving the appliance be careful not to damage the power cord EXTENSION CORD Because of potential safety hazards it is strongly recommended that you do not use an extension cord with this appliance However if you must use an extension cord it is absolutely necessary that it be a ULCULListed 3wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes INSTALLING STAINLESS STEEL HANDLE This appliance includes stainless steel handle that are not required to operate this appliance To install the handle please follow the be low instructions Handle Flat Was her Lock Washer Screw DoorFrame The gaskets are easily displaced b y hand no tools are necessary Use a flathead screwdriver to remove the two preinstalled decorative plugs from the back of doors Some beverage refrigerators have no decorative plugs Install the handle tightly as shown with two screws lock washers and flat washers provided DO NOT over tighten as this will cause damage to the handle and stainless steel door frame Replace the door gaskets to its original position quot
• Page 9 - English - : Installation REVERSING THE DOOR SWING OF YOUR BEVERAGE REFRIGERATOR Note All parts removed must be saved for proper reinstallation of the door This appliance has the capability of the door opening from either the left or right side The appliance is delivered to you with the door opening from the left side Should you desire to reverse the opening direction please follow the following reversal instructions 1 Remove the front ventilation grille 2 and the adjustable ventilation grille 1 by unscrewing the screws 3 amp 4 Figure 1 2 Remove the bottom hinge plate 5 by unscrewing the four lock screws 6 Be careful to hold the glass door firmly after removing the screws Figure 2 3 Gently pull down to remove the glass door from the right top hinge and place it on a padded surface to avoid the risk of damage then remove the right top hinge 7 Figures 3 amp 4 4 Unscrew and transfer the hinge pin of the bottom hinge plate 5 to the opposite side 5 Pop out the cover caps on the upper left side corner of the inside cabinet and use them to cover the screw holes on the right hand side 6 Screw the alternative left top hinge 9 included in the fittings on the left hand side of cabinet Figure 4 7 Relocate the door to the designated position Then screw the bottom hinge assembly on the left designated position and tighten it after the door is leveled Figure 2 8 Reassemble the ventilation grilles
• Page 10 - English - : It is recommended you install the appliance in a place where the ambient temperature is between 72º 78ºF 23º26ºC If the ambient temperature is above or below recommended temperatures the performance of the beverage wine refrigerator may be affected For example placing your appliance in extreme cold or hot conditions may cause interior temperatures to fluctuate NOTE When using the beverage wine refrigerator for the first time or restarting after being shut off for a long period of time there may be a few degree variance between the set temperature and the LED readout This is normal due the length of activation time The unit should return to normal after running for a few hours This unit will not raise its internal temperature if the ambient temperature where the unit is located is lower than the set temperature RECOMMENDED TEMPERATURE SETTINGS CONTROL PANEL GUIDE POWER To turn the appliance onoff press and hold the power key for 5 seconds To increase warm the set temperature by 1C or 1ºF To decrease cool the set temperature by 1C or 1ºF To turn the internal light onoff ºFºC SELECTOR Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit press and hold the LIGHT key for 5 seconds Conservation 49 57ºF 10 14ºC Red Wines 58 72ºF 15 22ºC DryWhite Wines 48 57ºF 9 14ºC Rose Wines 49 51ºF 10 11ºC Sparkling Wines 40 47ºF 5 8ºC O peration and Controls UP DOWN LIGHT NOTE If the appliance is unplugged encounter power interruption or turned off you must wait 3 5 minutes before restarting the appliance If attempted to restart before this time delay the appliance may not start SETTING THE TEMPERATURE CONTROL During normal operation the temperature display on the control panel shows the temperature inside the appli ance When the unit is plugged in for the first time the unit will power up automatically to the preset defaults The preset temperature is 54ºF 12ºC The temperature that you desire to set will increase 1ºC or 1ºF if you press the UP key once and will decrease 1ºC or 1ºF if you press the DOWN key once The display flashes while you make the setting To view the set temperature at any time press the UP or DOWN key the set temperature will temporarily flash in the display for 5 seconds Then the display shows the current internal temperature again
• Page 11 - English - : To change the f ilter NORMAL SOUNDS The unit is cooled by a compressor The compressor pumps coolant through the cooling system producing operating noise Even when the compressor cuts out noises caused by changes in temperature and pressure are unavoidable Operating noise will be most audible immediately after the compressor comes on It becomes quieter as the operating period continues The following noises are normal and occur from time to time Gurgling sound caused by the refrigerant flowing through the appliances coils Humming noise made by the compressor This noise can get louder for brief periods when the motor is switching on Crackingpopping sounds resulting from the materials contraction and expansion due to temperature variations Fan operating sound to circulate the air within the beverage cabin et Unusual noise is normally the result of improper installation Where the unit is installed in openplan kitchen or in partition walls the level of operating noise will be heard more acutely However this is due to the surrounding architecture and not to the unit NOTE An individuals perception of noise is directly linked to the environment in which the unit is located as well the specific type of models Our appliances are in line with interna tional standards for such appliance and in line with the latest technical developments Please remember that the noise of the compressor and the coolant circulating in the system is unavoidable TEMPERATURE MEMORY FUNCTION In the event of a power interruption power surge breaker switch etc the unit can remember the previous temperature settings When the power has restored the temperature display will show the current cabinet temperature INTERIOR LIGHT The interior light makes it easy to view your beverage labels and enhances the display of your collection The light can be turned on or off pressing the light button on the display CABINET SHELVES NOTE Do not cover any part of the shelves with aluminum foil or any other material that will prevent adequate air circulation within the cabinet This appliance is equipped with removable shelves To prevent damage to the door gasket make sure the door is opened completely before pulling the shelves out ACTIVATED CARBON FILTER The Whynter 834834 are equipped with one activated carbon filter which ensures optimum air quality within the beverage cabinet This filter counters and prevents any contaminants and odors from the ambient air affecting the taste of the beverage stored Replace the active carbon filter once a year If you are interested in purchasing an additional carbon filter please contact supportwhyntercom for retail sales information Operation and Controls Turn the filter cover 90 clockwise or counterclockwise and then remove the filter Insert the new filter in the vertical position Turn the filter cover 90 clockwise or counterclockwise until it click into position
• Page 12 - English - : BWR208SB Shelf 1 3 bottles Shelf 2 3 bottles Shelf 3 3 bottles Shelf 4 3 bottles Shelf 5 3 bottles Shelf 6 3 bottles Bottom 2 bottles 3 x 6 2 20 bottles standard size 750ml BWR308SB Shelf 1 5 bottles Shelf 2 5 bottles Shelf 3 5 bottles Shelf 4 5 bottles Shelf 5 5 bottles Shelf 6 5 bottles Bottom 3 bottles 5 x 6 3 33 bottles standard size 750ml Storage Wine bottles may differ in size and dimensions so the actual number of bottles can be stored may vary The 20 33 bottles capacity is the approximate maximum when storing traditional 750ml and includes bulk storage You may load your wine bottles in single row or by stacking while taking note of the following if you do not have enough bottles to fill your beverage wine refrigerator it is better to distribute the load throughout the beverage wine refrigerator to avoid quotall on topquot or quotall belowquot type loads You can remove or relocate adjustable shelves to accommodate larger type of bottles see removing shelves Keep small gaps between the walls and the bottles to allow air circulation Do not over load your wine refrigerator Avoid obstructing the internal fans located inside on the back panel of the beverage wine refrigerator Do not try to slide the shelves outwards beyond the fixed position to prevent the bottles from falling Do not pull out more than one loaded shelf at a time as this may cause the wine refrigerator to tilt forward if not properly installed DEFROSTING AND VENTILATION Your beverage refrigerator is designed with an automatic defrost system During offcycle the evaporator behind the rear wall of the unit defrosts automatically Condensation is collected in the drain at the back of the unit and flows through the drainage hole into the drip tray above the compressor The heat is transferred from compressor and evaporates any condensation that has collected in the drip tray Part of the remaining water within the beverage refrigerator is collected for humidity purposes NOTE Frost may accumulate on the evaporator if the unit is repeatedly opened in a high heat or high humidity location If this frost pattern does not clear within 24 hours your unit will require manual defrosting
• Page 13 - English - : REMOVING SHELVES To remove any of the shelves from the rail compartment move the shelf to the position where the notch of shelf is exactly under the plastic post and then lift it up and out In order to replace the shelf repeat steps described above in reverse And make sure to engage the shelves with the small pegs of the extended rails when the model is equipped with roller system Storage
• Page 14 - English - : Care and Maintenance CLEANING YOUR APPLIANCE Turn off the power unplug the appliance and remove all contents from the appliance and store them in a suitable place Clean the inside the door seal and the inside of the glass with a clean damp cloth Never use detergents or other substances that emit odors Always keep the door closed when cleaning the outside of the appliance Make sure no detergent odors penetrate into the appliance Clean the side panels and door surfaces with a clean and soft cloth If necessary use a moist cloth Alternatively use a microfiber cloth The humidity tray should be handwashed with water and detergent After cleaning always make sure the tray is thoroughly rinsed with clean water before replacing PREMISES POWER FAILURE In the event of a power interruption temperature settings automatically defaults to factory settings once power is restored Factory default temperature setting is 54 F To set a different desired temper ature refer to the quotSETTING THE TEMPERATUREquot and quot C and F SELECTORquot section on page 10 Most power failures are corrected within a few hours and should not affect the temperature of your appliance if yo u minimize the number of times the door is opened If the power is going to be off for a longer period of time you need to take the proper steps to protect your contents VACATION TIME Short vacations Leave the appliance operating during vacations of less than two days Long vacations If the appliance will not be used for an extended period remove all items and turn off the appliance Clean and dry the interior thoroughly MOVING YOUR APPLIANCE Remove all items inside the appliance Securely tape down we recommend using painters tape all loose items shelves inside your appliance Turn the adjustable legs up to the base to avoid damage Tape we recommend using painters tape the door shut Be sure the appliance stays secure in the upright position during transportation and protect the exterior of appliance with a blanket or similar item PREPARING FOR STORAGE If the beverage wine refrigerator will not be used for a long time or is to be moved to another place it will be necessary to defrost the unit and dry the interior Disconnect the beverage wine refrigerator from the power supply by removing the power plug from the wall socket Leave the door open to allow for air circulation and to prevent mold mildew and unpleasant smells CAUTION Store the unit out of the reach of children If you have children you may want to take additional precautions such as removing the door to prevent a child from being trapped inside the beverage wine refrigerator NOTE If the beverage wine refrigerator is unplugged encounter power lost or turned off you must wait 3 to 5 minutes before restarting the beverage refrigerator When the beverage wine refrigerator is used for the first time or restarted after having been shut off for a long time there could be a few degrees variance between the temperature you select and the one indicated on the display This is normal and it is due to the length of the inactivation time The appliance should be located in the coolest area of the room away from heat producing appliances and out of any direct sunlight Ensure that the appliance is adequately ventilated Never obstruct the air vents Close the door tightly and do not open the appliance too frequently or for a long period of time Store the content in an organized way Do not over load the appliance to allow air to circulate
• Page 15 - English - : Problem Possible Causes Solutions The appliance does not operate There is a power failure The appliance is not plugged in A fuse has blown or the circuit breaker is tripped Ensure the appliance is plugged in and the power outlet has power Replace the broken fuse or reset the breaker The appliance is not cold enough The set temperature too high The appliance is placed too close to a heat source The door is opened too often The door is not closed comple tely The door gasket does not seal properly The front bottom grille does not have sufficient ventilation Adjust the set temperature Keep the appliance away from sunshine or other heat sources Close the door tightly and do not open the door too frequently or for a long period of time Ensure the door gasket is not loose The front bottom grille must be completely unobstructed Decrease or increase the ambient room temperature To minimize internal temperature fluc tuation do not add large amount of contents at once Close the door tightly and do not open the door too frequently or for a long period of time Ensure the door gasket is not loose The ambient room temperature is too low or high A large amo unt of contents has been added to the appliance The d oor is opened too often The door is not closed completely The door gasket does not seal properly The appliance makes too much noise The noise may come from the flow of the refrigerant and ex pansion of the inside walls may cause popping and crackling noises Contraction and expansion of the inside walls may cause popping and crackling noises The appliance is not level The door does not close properly The appliance is not level The door was reversed and not properly installed The shelves are out of position It is normal that as each cooling cycle ends you may hear rattling or gurgling sounds caused by the flow of refrigerant in the appliance The high efficiency compressor may make a pulsating or high pitched sound Some popping or cracking noises are normal They are caused by expansion and contraction of the inside walls due to temperature changes Make sure the unit is on a hard and level surface Do not place the appliance on carpet See Operating Noises Make sure the appliance is on a hard and level surface Avoid placing the appliance on a carpeted or soft surface Correctly install the shelves Troubleshooting The appliance turns itself on and off frequently
• Page 16 - English - : Troubleshooting Problem Possible Causes Solutions Display flashing Set temperature has not been reached It is normal for the display to flash until the unit reaches the set temperature Please note that the unit may take unto 24 hours to reach the set temperature if the cabinet is full Display E1 E2 E5 E6 EU LO or HI E1 E2 air temperature sensor error E5 E6 defrost sensor error EU display error LO low temperature alarm HI high temperature alarm Contact Whynter Customer Support The icon is lit up and flashing in the temperature display The display temperature is out of the range Only temperatures within the range 16 99F9 37C the appliance can display will be shown If the tempera ture is not within this range the icon will be displayed instead That is nor mal
• Page 17 - English - : ONE YEAR LIMITED WARRANTY This WHYNTER product is warranted to the original owner purchased from an authorized Whynter dealer within the 48 US continental states for one year from the original purchase date against defects in material and workmanship under normal residential usage Should your WHYNTER product prove defective within one year from the date of purchase contact Whynters Customer Support Team with the serial number and proof of purchase to make a warranty claim A Return Authorization Number must be issued before returning any parts or products Parts or products received without a Whynter issued Return Authorization Number will be refused Under this warranty Whynter will repair or replace any parts found defective with new or remanufactured parts or exchange the defective product with a new refurbished or remanufactured product at our discretion All defective products and parts covered by this warranty will be repaired or replaced on a mailin basis to Whynters Service Center This warranty is not transferable After the expiration of the warranty the cost of labor and parts will be the responsibility of the original owner Return freight is prepaid by Whynter within two months of purchase After two months to one year the customer will be responsible for the return freight cost to Whynters Service Center Please package the product carefully in its original packaging to avoid damage in transit Whynter is not responsible for damage resulting from shipper mishandling or improper packaging Please retain the original box and packaging materials THIS WARRANTY DOES NOT COVER Acts of God such as fire flood hurricanes earthquakes and tornadoes Improper power supply such as power surge low voltage defective household wiring or inadequate fuses Use in commercial or industrial applications Damage accidental or otherwise to the WHYNTER Beverage Wine Refrigerator while in the possession of a consumer not caused by a defect in material or workmanship Damage caused by consumer misuse tampering or failure to follow the care and special handling provisions in the instructions Damage to the finish of the case or other appearance parts caused by wear Damage caused by repairs or alterations to the product by anyone other than authorized by the manufacturer Removal Replacement Packaging Freight and Insurance cost for the warranty service DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMERS SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE The warranty product contents and specifications are subject to change at any time without notice please refer to wwwwhyntercom for the most current information To register your warranty please visit wwwwhyntercom and fill out the online Warranty Registration form Please be sure to include a copy of your purchase invoice To obtain service or information contact Whynter LLC via email at supportwhyntercom or call 866WHYNTER 8669496837 Copyright 2021 Whynter LLC wwwwhyntercom