Loading ...
Loading ...
Disposal Instructions
Waste and Disposal Instructions
3
It is advisable to remove the Lithium Battery from this
product and/or remote control when it is not used for an
extended period of time. This will help to extend battery
life and avoid possible damage to the product and/or
remote control.
BATTERY REMOVAL:
Perform the following steps to remove the battery from
the product and/or remote control:
1. Before removing the Lithium Battery, rst discon-
nect the AC Power Cord and/or AC/DC Adapter
from this product.
Note: Step 1 is not required when removing the Lithium
Battery from a remote control.
2. Press the tab and lift up on the Backup Battery Cov-
er and temporarily place it aside. Refer to gures 1
and 2.
3. When removing the battery from a remote control
proceed to step 4. To remove the battery from a
product proceed to step 5.
4. Refering to figure 3, press on the bottom edge of
the battery to release the battery from the molded
battery socket. Then remove the battery from inside
of the Remote Control. Proceed to step 6.
5. Refering to gure 4, use a small pocket size screw
driver (or other suitable tool) and carefully insert the
tip of the tool between the metal tab of the battery
socket and the left side of the battery. Then rotate the
tool to release the battery from the socket. Remove
the battery from inside of the product.
6. Reinstall the Battery Cover.
7. Store the battery in a cool dry place for future use or
dispose of the battery in accordance with the local
regulations for lithium battery disposal. Batteries
should never be thrown away or incinerated.
BATTERY INSTALLATION:
Perform the following steps to install the battery into the
product and/or remote control:
8. Before installing the Lithium Battery, rst discon-
nect the AC Power Cord and/or AC/DC Adapter
from this product.
Note: Step 8 is not required when installing the Lithium
Battery into a remote control.
CAUTION:
Danger of explosion if the battery is
incorrectly installed. Only install one of
the approved Lithium Batteries listed
below.
Long Life Lithium Coin Cell type battery is used in this
product and/or supplied remote control. is product
and/or supplied remote control may be supplied with a
battery depending on the country where this product
is purchased. When purchasing a battery for use in this
product and/or remote control, refer to the following list:
This product and/or the remote control supplied with
this product may contain a coin/button cell battery.
If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can
lead to death. Keep new and used batteries away from
children. If the battery compartment does not close
securely, stop using the product and/or remote control
and keep it away from children. If you think batteries
might have been swallowed or placed inside of the
body, seek immediate medical attention.
WARNING:
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
AVERTISSEMENT:
NE PAS INGÉRER L’ACCUMULATEUR,
RISQUE DE BRỦLURE CHIMIQUE
[La telecommande fournie avec] Ce product con-
tient un accumulateur bouton. En cas d’ ingestion,
l’ accumulateur bouton, peut causer des brulures
internes severes en a peine 2 heures qui peuvent etre
mortelles. Conserver les accumulateurs neufs usages
hors de portee des enfants. Sile compartiment de l’
accumulateur ne se ferme pas de maniere sure, ne
plus utiliser le produit et et le tenir hors de portee des
enfants. Encas de soupcon d’ingestion d’un accumu-
later ou d’introduction dans une partie quelconque du
corps, demander immediatement un avis medical.
Lithium Battery Type
Battery Removal or Installation
Lithium Battery
Figure 1
TAB
Figure 2
LIFT
UP
Figure 8
C
R
2
0
3
2
Contact
Points
Figure 7
C
R
2
0
3
2
CR2032
3V
Battery
Figure 3
Figure 4
CR2032
3V
Figure 6
CR2032
3V
Tabs
Figure 5
Battery
Socket
9. Press the tab and lift up on the Backup Battery Cov-
er and temporarily place it aside. Refer to gures 1
and 2.
10. When installing the battery into the remote control
proceed to step 11. To install the battery into a
product proceed to step 12.
11. Orient the battery so the + symbol (engraved into
one side of the battery) is facing up. Refer to figure
7. Then insert the battery into the socket. Make
sure the battery is touching both contact points and
is seated in the socket. Refer to figure 8.
12. Orient the battery so the + symbol (engraved into
one side of the battery) is facing up. Refer to fig-
ures 5 and 6. Then insert the battery into the sock-
et. Make sure the battery is touching both contact
points and is seated in the socket.
13. Reinstall the Battery Cover.
When discarding the unit, comply with local rules or
regulations. Batteries should never be thrown
away or incinerated but disposed of in accor-
dance with the local regulations concerning
battery disposal.
North American Waste of Electrical and Electronic
Equipment Directive
Lithium Battery, Types, Removal and Installation
Approved Lithium Batteries
Brand IEC No. ANSI/NEDA No.
Energizer CR2032 5004LC
1
Panasonic CR2032(PA/1B)
1
5004LC
1
1
CR Lithium Coin Cells contain Perchlorate - special handling may
apply. For additional information go to https://www.dtsc.ca.gov/
hazardouswaste/perchlorate/
ATTENTION:
Danger d’explosion si la pile n’set
pas remplacée correctement. Installer
uniquement l’une des piles au lithium
approuvées énumérées ci dessous.
Loading ...