Loading ...
MODELS BWT1304SS • BWT1304SSB •
BWT2304SS • BWT2304SSB
Page 2
CLEANING & MAINTENANCE
Proper maintenance of the Range Hood will assure proper
performance of the unit.
MOTOR
The motor is permanently lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the blower with the exact service blower.
GREASE FILTERS
The grease filters should be cleaned frequently. Use a warm
dishwashing detergent solution. Grease filters are dishwasher
safe.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filters may occur if using phosphate
detergents, or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered by
the warranty.
Remove grease filters by pulling down on the metal latch tab. This
will disengage the filters from the hood. Tilt the filters downward
and remove.
NON-DUCTED RECIRCULATION FILTERS
The non-ducted recirculation filters should be changed every
6 months. Replace more often if your cooking style generates
extra grease, such as frying and wok cooking. Turn the filter
mounting tabs to remove filter and replace.
GLASS PANEL (Models BWT1304SSB and BWT2304SSB)
Hot water with mild soap or glass cleaner is all that is usually
needed. When using mild soap, rinse with clear water. Wipe dry
with a clean, soft cloth to avoid water marks.
STAINLESS STEEL CLEANING
DO:
• Regularly wash with clean cloth or rag soaked with warm water
and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning.
Wipe dry completely.
• You may also use a specialized household stainless steel
cleaner.
DON’T:
• Use any steel or stainless steel wool or any other scrapers to
remove stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the
hood. During construction/renovation, cover the range hood to
make sure no dust sticks to the stainless steel surface.
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel
• Any products containing: chloride, fluoride, iodide, bromide
will deteriorate surfaces rapidly.
• Any combustible products used for cleaning such as acetone,
alcohol, ether, benzol, etc., are highly explosive and should
never be used close to a range.
OPERATION
BWT1304SS AND BWT2304SS MODELS.
Push the light button to turn the lights on and off.
Push the blower controls to select low, medium, or high blower
speed (for each speed selected, its indicating light will beam).
Press on the current blower speed another time to stop it.
While the blower is activated, press the 5-minute delay button
once (its indicating light will beam) to get the hood running for
5 minutes and then turn off automatically.
When the 5-minute delay is activated, changing the blower
speed will cancel the 5-minute delay function.
To cancel the delay off function before the end of the 5-minute
cycle, press again on 5-minute delay push button or select an
other blower speed.
BWT1304SSB AND BWT2304SSB MODELS.
HC0095
LIGHT
ON/OFF
LOW MED. HIGH
BLOWER CONTROLS
5-MINUTE
DELAY
Tap on the light button to turn the lights on; the backlight of the
button will also turn on. Tap another time to turn off the lights
(backlight of the light button will also turn off).
Tap on the power on/off button: the backlight of the button will
turn on, the blower will work on low speed and the light will be
on. The backlight of the blower controls and light will be on too.
Tap another time on the power on/off button; the blower and the
light will turn off as well as all backlights.
Tap the + blower control; the backlight of button will turn on, the
blower starts to work on low speed and the LED display shows 1.
Tap another time for the blower to reach medium speed; LED
display shows
2. Tap again for the blower to reach high speed;
the LED display will show 3.
Tap the
- blower control; the backlight of button will be on, the
blower speed will decrease one speed and the LED display will
show the current working speed. When the blower is set on low
speed (1), tapping another time will turn off the blower (as well
as the backlight of the - blower control).
While the blower and lights are on, tap on the 5-minute delay
button once (its backlight will turn on) to get the hood running for
5 minutes and then turn off automatically blower and lights.
To cancel the delay off function before the end of the 5-minute
cycle, tap again on the 5-minute delay button or change the
blower speed using one blower control (+ or -). The backlight
of the 5-minute delay button will then turn off.
8.
5-MINUTE
DELAY
LIGHT
ON/OFF
BLOWER
CONTROLS
POWER
ON/OFF
LED
DISPLAY
Loading ...
Loading ...
Loading ...