LBF 5B User Manual

Loading ...

Troubleshooting

Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.

* Only available in selected models.

Problem: Possible causes / Solutions:

The dishwasher does not start or cannot

be controlled

• SwitchofftheappliancebypressingtheON/OFFbutton,switchitbackonafter

approximately one minute and reset the program.

• Theappliancehasnotbeenpluggedinproperly.

• Thedishwasherdoorhasnotbeenshutproperly.

The door won’t close • Thelockwasreleased.Stronglypushthedooruntila“clacking”noiseisheard.

No water drains out from the

dishwasher.

• Thedishwashercyclehasnotyetnished.

• Thewaterinlethoseisbent(see Installation).

• Thedrainductisblocked.

• Thelteriscloggedupwithfoodresidues.

The dishwasher makes excessive noise. • Thedishesarerattlingagainsteachotheroragainstthesprayerarms.

• Anexcessiveamountoffoamhasbeenproduced:thedetergenthasnotbeen

measured out correctly or it is not suitable for use in dishwashers (see Start-up

and use).

The dishes and glasses are covered in a

white lm or limescale deposits.

• Theleveloftherenedsaltisloworthedosagesettingisnotsuitedtothe

hardness of the water (see Rinse aid and salt).

• Thelidonthesaltdispenserisnotclosedproperly.

• Therinseaidhasbeenuseduporthedosageistoolow.

The dishes and glasses are streaked or

have a bluish tinge.

• Therinseaiddosageistoohigh.

The crockery has not been dried

properly.

• Awashcyclewithoutadryingprogramhasbeenselected.

• Therinseaidhasbeenuseduporthedosageistoolow(see Rinse aid and

salt).

• Therinseaiddispensersettingisnotsuitable.

• Thecrockeryismadefromnon-stickmaterialorplastic.

The dishes are not clean. • Theracksareoverloaded(seeLoadingtheracks).

• Thecrockeryhasnotbeenarrangedwell.

• Thesprayerarmscannotmovefreely.

• Thewashcycleistoogentle(see Wash cycles).

• Anexcessiveamountoffoamhasbeenproduced:thedetergenthasnotbeen

measured out correctly or it is not suitable for use in dishwashers (see Start-up

and use).

• Thelidontherinseaidcompartmenthasnotbeenshutcorrectly.

• Thelterisdirtyorblocked(seeCareandmaintenance).

• Therenedsaltlevelislow(seeRinseaidandsalt).

The dishwasher does not take any water

in - Tap shut-off alarm

(several short beeps are emitted*)

(theDryingandEndindicatorlightsash).

• Thereisnowaterinthemainssupply.

• Thewaterinlethoseisbent(seeInstallation).

• Turnonthetapandtheappliancewillstartafterafewminutes.

• Theappliancelockhasbeenactivatedbecausenoactionwastakenwhenthe

beeps*sounded.SwitchofftheapplianceusingtheON/OFFbutton,turnonthe

tap and switch the appliance back on after 20 seconds by pressing the same

button. Re-program the appliance and restart the wash cycle.

Water inlet hose alarm / Water inlet lter

blocked

(the Washing, Drying and End indicator

lightsashes).

• SwitchofftheappliancebypressingtheON/OFFbutton.Shutoffthewatertap

toeliminatetheriskofoodingandremovetheplugfromtheelectricalsocket.

 Makesurethewaterinletlterhasnotbecomeblockedbyimpurities(see“Care

andmaintenance”chapter).

Loading ...

User Manual - Page 13