User Manual Kwikset 818SCEXHFL - 15 SMT Door Lock/Deadbolt Lever Handle Lock

Documents for Kwikset 818SCEXHFL 15 SMT

The following documents are available:
User Manual Installation Instruction
  • Instructions to re-key a SmartKey Security lock - (English) Download
Photos
818SCEXHFL 15 SMT photo
Installation Guide
Guía de instalación
18003275625
www.kwikset.com
If drilling a new door, use
the supplied template and
the complete door drilling
instructions available at
kwikset.com/doorprep.
Si va a perforar una puerta
nueva, utilice la plantilla
suministrada y las instrucciones
completas para la perforación
de la puerta estan disponibles
en kwikset.com/doorprep
Fold the supplied template along
the fold line and place on the
exterior side of your door so that
the holes in the template are aligned
with the holes in your door.
Doble la plantilla suministrada a lo largo
de la línea de pliegue y coloquela sobre
el borde exterior de su puerta de manera
que los oriicios en la plantilla queden
alineados con los oriicios de su puerta.
through door
a través de la puerta
If you already have the bottom hole
drilled in your door, conirm that its
location falls between the highest
and lowest holes at the bottom of
the template. If it does not fall within
this range, drill a new hole in step 3.
If the bottom hole is not drilled, use
the template to mark the location of
the new hole on your door. Make sure
it is aligned with the other holes in the
door. Drill a new hole in step 3 at the
91/8" (232 mm) mark on the template.
Si el oriicio inferior está perforado
de antemano en su puerta, conirmar
que está alineado con uno de los
oriicios inferiores de la plantilla. Si
no cae dentro de este rango perforar
un nuevo oriicio en el paso 3.
Si el oriicio inferior no se perfora, utilice
la plantilla para marcar la ubicación del
oriicio nuevo en la puerta. Asegúrese
de que el oriicio está alineado con los
otros oriicios en la puerta. Perfora un
nuevo oriicio en el paso 3 en la marca
de 232 mm (91/8") en la plantilla.
23/8" (60 mm)
or • o
23/4" (70 mm)
13/4" — 21/4"*
44 mm — 57 mm*
51/2"
140 mm
21/8"
54 mm
21/8"
54 mm
1"
25 mm
1"
25 mm
exterior
exterior
exterior
exterior
exterior
exterior
7/16"
11.11 mm
*Call Kwikset to order
a service kit for 21/4"
(57 mm) thick doors.
*Llame a Kwikset para
pedir un kit de servicio
para puertas gruesas
con un espesor de
entre 57 mm (21/4”).
Rotate the front of
the latch to extend it.
Gire el pestillo frontal
para alargar.
Hold the latch in front of the
door hole, with the latch case
lush against the door edge.
Sostenga el pestillo en frente
del oriicio de la puerta, con
la cubierta del pestillo al ras
con el borde de la puerta.
If the D-shaped hole is centered
in the door hole, no adjustment
is required. Proceed to step 6.
If the D-shaped hole is NOT
centered, adjust latch. See
“Latch Adjustment” (step 5C)
Si el oriicio en forma de “D”
está centrado con el oriicio
de la puerta, no se requiere
ajustarlo. Vaya al paso 6.
Si el oriicio en forma de “D”
NO está centrado, ajuste el
pestillo. Consulte “Ajuste
del pestillo” (el paso 5C).
Latch Adjustment (only if needed)
Ajuste del pestillo (si es necesario)
A
B
C
Adjust the backset of the top latch (if needed)
Ajuste la distancia al centro del pestillo superior (si es necesario)
5
A
latch case
cubierta
del pestillo
180°
centered
centrado
not centered
no centrado
Make sure the curve is on
the bottom of the latch.
Asegurarse de que la
curva este en la parte
inferior del pestillo.
A
180°
D-shaped hole
oriicio en forma de “D”
64483003 Rev 03
818
wood block
bloque de
madera
Parts in the box
Piezas en la caja
Required tools
Herramientas
necesarias
Additional tools
(if needed)
Herramientas
adicionales
(si es necesario)
Latches and strikes*
Pestillos y placas*
Deadbolt
Cerrojo
Handleset
Conjunto de manija
Lever Option 2: Hidden Screws
Opción 2: Palanca con
tornillos escondidos
Lever/Knob Option 1: Visible Screws
Opción 1: Palanca/perilla
con tornillos visibles
J
N1
N2
P
S
V
WT
E1
E2
F1
F2
F3
B
G
K
H
L
M
R U
A2 A3A
C D
*Latch and strike options vary by product.
* Las opciones de pestillos y placas varían según el producto.
1 / 4
A
B
Prepare door and check dimensions
Prepare la puerta y revise las dimensiones
1
Drill new bottom hole (if needed)
Perfore un nuevo oriicio inferior (si es necesario)
3
Extend the top latch bolt
Extienda el perno del pestillo superior
4
Conirm bottom hole location
Conirme la ubicación del oriicio inferior
2
Loading ...
Loading ...
Loading ...