Loading ...
Introduction
Congratulations on the purchase of your Swann Su-
per HD Camera.
• Enjoy day & night protection with the latest
thermal-sensing security & have a crystal clear
bird’s eye view of your premises
• See what’s happening in any light with infrared
cut filter & powerful LEDs
• State-of-the-art True Detect™ PIR motion sen-
sor is designed for security applications with
the ability to reliably detect people, cars, large
pets & other heat-generating large objects
• With discreet dome styling & sturdy aluminium
construction, the camera suits indoor & out-
door applications with an IP66 rating for any
weather conditions & cable threaded through
the mounting bracket for added protection
Important instructions
1. Make sure the camera is fixed correctly and stable
if fastened in place.
2. Only use the supplied power adapter (12V) and
power splitter (if supplied).
3. Do not operate if wires and terminals are exposed.
Please note: Have a look at the camera location tips
included with your DVR, to select the best location for
your camera (the camera location tips provided here
are for general purpose only).
Important note: All jurisdictions have specific laws
and regulations relating to the use of cameras. Be-
fore using any camera for any purpose, it is the buy-
er’s responsibility to be aware of all applicable laws
and regulations that prohibit or limit the use of cam-
eras.
The camera can be mounted onto a flat vertical or horizontal surface
and must be of sufficient strength to hold the camera.
→ Hold the dome enclosure (1) and the dome ring (2) then rotate
the mounting bracket (3) clockwise to remove it from the
camera.
→ Position the camera bracket (4) in the location you want to
mount it, and mark the mounting holes on the surface to
position the screws (a mounting template has been included).
→ Using the appropriate screws for the surface you are mounting
to, secure the bracket in place.
→ Run the cable then place the camera into the dome enclosure
and dome ring and aim the camera to the desired position. The
camera can be rotated left or right or up and down. Check the
image on your DVR and make adjustments as necessary.
→ After you’ve finished adjusting the viewing position, rotate the
dome ring to the mounting bracket counter clockwise to lock
the position in place.
1. Take into consideration what you want to monitor
and where you’ll get the best view of it.
2. How you’re going to connect the camera to your
monitoring system; remember that cables and
connections should be kept out of the weather.
3. How to keep the camera out of harm’s way. It’s
recommended to mount your camera at an elevated
position.
4. Place your camera as close to the area of interest
as practicable. The best position is from about
13ft/4m above looking slightly down, keeping in mind
the details you are looking for.
5. Although the sky looks nice when you look at the
live view from your camera, it is an unlikely direction
for an offender to approach. Make sure your camera
has minimal sky in it as the light in daylight can make
the foreground of the image darker.
6. Think about the most likely way a potential offender
may approach your home, use your camera to give
you the best coverage of these areas.
7. The camera’s casing is resistant to different
weather conditions and tampering. It would take an
overwhelming event to damage the housing.
8. Even though the camera is weather and water-
resistant, prolonged exposure to adverse weather
conditions such as sunlight or excessive moisture,
may eventually damage the internal components of
the camera and adversely affect its performance.
9. Run cables inside a wall cavity or other protected
enclosure, and ensure that all wiring and connectors
are insulated and protected from moisture.
10. Don’t put your cable near live electrical wiring.
AC electricity generates radio “noise” which can
interfere with the signal from your camera.
1. Connect the video output and
power input connections on the
camera to the corresponding
connections on the supplied video &
power cable.
2. Connect the supplied power
splitter to the power input on the
video & power cable (repeat this step
if multiple cameras are included).
3. Connect the supplied power
adapter to the other end of the power
splitter then connect the power
adapter to a spare wall socket.
4. Connect the video output on the
video & power cable to an available
camera input on your DVR. Twist the
connection to lock it in place.
1
Connecting the Camera2 Mounting the Camera3
Camera Location Tips4
For single camera packs, connect the supplied power adapter
directly to the power input on the video & power cable.
2 3
Power Input
Video Output
1
Twist to lock
connectors
Video Input
Video & Power Cable
Connect this to your DVR
Power Splitter
connects here
Power Output
Power Adapter
connects here
Power Splitter
Power Adapter
Video & Power Cable
connects here
Connect to a spare
power outlet
LANLAN
VGAVGA
7 5 3 1
8 6 4 2
VIDEO INPUTVIDEO INPUT
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO
INPUT
AUDIO
INPUT
3 1
4 2
12V12V
RS485RS485
4
4
1
3
2