Rear Speaker
Operating Instructions
SA-RS3S
5-011-527-11(1)
©2020 Sony Corporation Printed in Malaysia
Owner’s Record
The model and serial numbers are located on the
bottom of the speakers.
Record the serial numbers in the space provided
below. Refer to them whenever you call upon your
Sony dealer regarding this product.
Model No. SA-RS3S
Serial No.
About compatible
models for the rear
speaker
The SA-RS3S rear speaker works only with the
specified model. For information about compatible
models, visit Sony's website.
In these Operating Instructions, the operations are
described for speakers used with the compatible
model HT-A7000.
Parts and Controls
Front
Power indicator
– Flashes slowly (green): The rear speaker is not
connected to a compatible model.
– Lights up (green): The rear speaker is connected
to a compatible model.
– Flashes twice repeatedly (green): The rear
speaker is attempting to connect to a compatible
model.
– Flashes/lights up (amber): The software is
updating.
– Lights up (red): The rear speaker is in standby
mode.
– Turns off: The rear speaker is turned off.
Note
The brightness of the power indicator syncs with the
DIMMER settings of a compatible model.
Rear
Wall mount hole
(power) button
LINK button
Mounting hole for the general speaker stand
AC inlet
Installation
Installing on the Floor
The following illustration is the installation example
to use the speakers with the compatible model
HT-A7000 and an optional subwoofer.
REAR R
SA-RS3S
REAR L
1 Check the right and left rear speakers using the
label on the bottom of them.
“REAR R” is for the right, “REAR L” is for the left.
2 Install the speakers behind your listening
position.
The following installations are recommended to
enjoy the surround sound effectively.
– Align the height position of the speaker with
your ear.
– Turn the speakers to your listening position.
Note
Lay the bottom (the face on which there is a label)
down to install the speaker. Installations other than
above are not supported.
Tip
To obtain a good surround sound, set the speaker
distance from your listening position by using the
setup menu of a compatible model.
For details, refer to the Operating Instructions
supplied with a compatible model.
Mounting on the Wall
The following illustration is the installation example
to use the speakers with the compatible model
HT-A7000 and an optional subwoofer.
REAR R
SA-RS3S
REAR L
Note
• Have the installation done by a Sony dealer or
licensed contractor and pay special attention to
safety during the installation.
• Sony shall not be held responsible for accidents or
damage caused by improper installation,
insufficient wall strength, improper screw
installation or natural disaster, etc.
1 Prepare a screw (not supplied) that is suitable
for the wall mount hole on the rear of the
speakers.
4 mm (3/16 in)
More than 30 mm (1 3/16 in)
Hole on the rear of the rear speaker
5.0 mm
(13/64 in)
10 mm
(13/32 in)
2 Decide the wall mounting position of the
speaker and fasten the screw there.
Approx.
13.5 mm
(approx.
9/16 in)
3 Hang the wall mount hole on the screw.
Check the label on the bottom of the speakers.
“REAR R” is for the right, “REAR L” is for the left.
Note
Prepare screws (not supplied) that are suitable for
the wall material and strength. As a plasterboard wall
is especially fragile, attach the screws securely in the
wall beam. Mount the speakers onto a reinforced
wall making sure that the heights of the right and left
speakers are equal.
Connection
Tip
You can connect the optional subwoofer with a
compatible model in the following way when
installing it too.
1 Turn on a compatible model.
2 Connect the AC power cords (mains leads)
(supplied) to the rear speakers, and then
connect the cords to the AC outlets (mains).
3 Make sure that the power indicators on the
speakers light in green.
When the power indicators light in green, the
connection between the speakers and a
compatible model is established.
If the connection is not established, connect the
speakers to a compatible model manually. For
details, see “If the Connection is not Established
Automatically”.
If the Connection is not Established
Automatically
If you cannot connect the speakers to a compatible
model automatically or you use multiple compatible
models and want to specify the compatible model
for connecting the speakers, perform the manual
connection.
The following operation is described for speakers
used with the compatible model HT-A7000. Use the
remote control supplied with the compatible model
HT-A7000 when performing this operation.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
1 Press HOME.
The home menu appears on the TV screen.
2 Select [Setup] - [Advanced Settings] on the
home menu.
3 Select [Speaker Settings] - [Wireless Speaker
Settings] - [Start manual linking].
The [Start manual linking] screen appears on the
TV screen.
4 Press LINK on the speaker.
The power indicator of the speaker that had LINK
pressed flashes twice repeatedly in green.
5 Select [Start].
The manual link starts.
The connecting process appears on the TV screen.
To cancel the manual link, select [Cancel].
6 When [Rear Speaker (R)] and [Rear Speaker (L)]
display [Connected], select [Finish].
7 Press .
The link is established and the power indicator of
the speakers lights in green.
Note
• If you perform [Start manual linking], [Link mode]
of [Wireless Speaker Settings] is set to [Manual]
automatically.
• Only the speakers for which [Connected] has been
displayed in Step 6 connect to a compatible model.
If the connection of the speakers cannot be
established, perform the manual connection again.
If Wireless Transmission is Unstable
If you use multiple wireless systems, such as a
wireless LAN, the wireless signals may become
unstable. In this case, the transmission may be
improved by changing the following setting.
The following operation is described for speakers
used with the compatible model HT-A7000. Use the
remote control supplied with the compatible model
HT-A7000 when performing this operation.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
1 Press HOME.
The home menu appears on the TV screen.
2 Select [Setup] - [Advanced Settings] on the
home menu.
3 Select [Speaker Settings] - [Wireless
Speaker Settings] - [RF Channel].
4 Select the setting you want.
• [On] (default setting): Normally select this. The
system automatically selects the better channel
for transmission. Stronger mode for wireless
interference.
• [Off]: The system selects a channel from the
limited frequency band to prevent external
wireless interference. If sound dropping occurs
while [On] is selected, it may be improved by
selecting [Off].
Note
• If you change the [RF Channel] setting from [Off] to
[On], it may take 1 minute to reconnect.
• A compatible model may not meet this setting
depending on countries/regions where you
purchase it.
Troubleshooting
If you experience any of the following difficulties
while using the rear speakers, use this
troubleshooting guide to help remedy the problem
before requesting repairs. Should any problem
persist, consult your nearest Sony dealer.
Be sure to bring all of your rear speakers, a
compatible model and optional subwoofer (not
supplied) even if it seems as though only one has a
problem, when you request to repair.
The following solutions are described for speakers
used with the compatible model HT-A7000.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
No sound is heard from the rear speakers.
q Make sure the AC power cord (mains lead) of the
rear speaker is connected properly.
q If the power indicator on the rear speaker does not
light, try the following.
– Make sure the AC power cord (mains lead) of the
rear speaker is connected properly.
– Press (power) of the rear speaker to turn on
the power.
q If the power indicator on the rear speaker flashes
slowly in green or lights in red, try the following.
– Move the rear speaker to a location near a
compatible model so that the power indicator on
the rear speaker lights in green.
– Follow the steps in “If the Connection is not
Established Automatically.”
– Check the wireless connection status. For details,
refer to the Operating Instructions supplied with
a compatible model.
q If the power indicator on the rear speaker flashes
in red, press (power) of the rear speaker to turn
off the power and check whether the ventilation
holes of the rear speaker is blocked or not.
q Press REAR + on the remote control of a
compatible model to increase the volume of the
rear speakers.
q If you change the [RF Channel] setting of a
compatible model from [Off] to [On], it may take 1
minute for the sound to be output.
q If the power indicator flashes in red, disconnect
the AC power cord (mains lead) of the rear speaker
from the AC outlet (mains) and reconnect it again.
Sound skips or has noise.
q If there is a device nearby that generates
electromagnetic waves, such as a wireless LAN or
a microwave oven in use, locate the rear speakers
and a compatible model apart from that device.
q If there is an obstacle between a compatible
model and the rear speakers, move or remove the
obstacle.
q Locate a compatible model and the rear speakers
as close as possible.
q Switch the network connection of the TV or Blu-ray
Disc player from wireless to wired.
Specifications
Amplifier section
U.S. models:
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(FTC)
With 6 ohms loads, both channels driven, from 200 -
20,000 Hz; rated 20 W per channel minimum RMS power,
with no more than 1% total harmonic distortion from 250
mW to rated output.
POWER OUTPUT (reference)
50 W (per channel at 6 ohms, 1 kHz)
Canadian models:
POWER OUTPUT (reference)
50 W (per channel at 6 ohms, 1 kHz)
Speaker system
2-way 2 speaker system
Bass reflex
Speaker
Woofer: 46 mm × 54 mm (1 13/16 in × 2 1/4 in) cone type
Tweeter: 16 mm (21/32 in) dome type
Power requirements
120 V AC, 60 Hz
Power consumption
On: 11 W
Standby mode: 1 W or less
Turned off: 0.5 W or less
Dimensions (w/h/d) (approx.)
100 mm × 187 mm × 100 mm (4 in × 7 3/8 in × 4 in)
(projecting parts not included)
Mass (approx.)
1.1 kg (2 lb 7 oz)
Wireless transmitter/receiver section
Communication system
Wireless Sound Specification Version 4.0
Frequency band
5 GHz
Modulation method
OFDM
Included items
• Rear speaker R (1), Rear speaker L (1)
• AC power cords (mains leads) (2)
• Operating Instructions (1)
Important information
on software
This product contains software that is subject to the
GNU General Public License (“GPL”) or GNU Lesser
General Public License (“LGPL”). These establish that
customers have the right to acquire, modify, and
redistribute the source code of said software in
accordance with the terms of the GPL or the LGPL.
For the method to confirm the GPL, LGPL and other
software licenses contained in the rear speakers,
please refer to the Operating Instructions of a
compatible model.
When you use the compatible model HT-A7000,
please refer to [Software License Information] under
[Setup] - [Advanced Settings] - [System Settings]
on the home menu.
The source code for the software used in this product
is subject to the GPL and LGPL, and is available on
the Web. To download, please access the following:
URL:
http://oss.sony.net/Products/Linux
Please note that Sony cannot answer or respond to
any inquiries regarding the content of this source
code.
All other trademarks are trademarks of their
respective owners.
WARNING
To reduce the risk of fire or electric shock, do not
expose these speakers to rain or moisture.
The speakers are not disconnected from the mains as
long as it is connected to the AC outlet, even if the
speakers themselves have been turned off.
To reduce the risk of fire, do not cover the ventilation
opening of the speakers with newspapers,
tablecloths, curtains, etc.
Do not expose the speakers to naked flame sources
(for example, lighted candles).
To reduce the risk of fire or electric shock, do not
expose these speakers to dripping or splashing, and
do not place objects filled with liquids, such as vases,
on the speakers.
As the main plug is used to disconnect the speakers
from the mains, connect the speakers to an easily
accessible AC outlet. Should you notice an
abnormality in the speakers, disconnect the main
plug from the AC outlet immediately.
Do not install the speakers in a confined space, such
as a bookcase or built-in cabinet.
Do not place this product close to medical
devices.
This product (including accessories) has magnet(s)
which may interfere with pacemakers, programmable
shunt valves for hydrocephalus treatment, or other
medical devices. Do not place this product close to
persons who use such medical devices. Consult your
doctor before using this product if you use any such
medical device.
Indoor use only.
For the speakers
The nameplates are located on the bottom of the
speakers.
For the customers in the U.S.A.
NOTE:
These speakers have been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
These speakers generate, use and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If these speakers
do cause harmful interference to radio or television
reception, which can be determined by turning the
speakers off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the speakers and
receiver.
– Connect the speakers into outlets on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
If you have any questions about this rear speaker:
Visit: www.sony.com/electronics/support
Contact: Sony Customer Information Service Center
at 1-800-222-Sony(7669)
Write: Sony Customer Information Service Center
12451 Gateway Blvd., Fort Myers, FL 33913
Supplier's Declaration of Conformity
Trade Name: SONY
Model: SA-RS3S
Responsible Party: Sony Electronics Inc.
Address: 16535 Via Esprillo, San Diego, CA 92127
U.S.A.
Telephone Number: 858-942-2230
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate these speakers.
These speakers must not be co-located or operated
in conjunction with any other antenna or transmitter.
These speakers comply with FCC radiation exposure
limits set forth for an uncontrolled environment and
meet the FCC radio frequency (RF) Exposure
Guidelines. These speakers should be installed and
operated keeping the radiator at least 20cm or more
away from person’s body.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software,
which is the passed down through the MAC, through
the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the
MAC. These are the only ways the digital baseband
portion will turn on the RF transmitter, which it then
turns off at the end of the packet. Therefore, the
transmitter will be on only while one of the
aforementioned packets is being transmitted. In
other words, this device automatically discontinue
transmission in case of either absence of information
to transmit or operational failure.
Frequency Tolerance: ±20 ppm or less
For the customers in Canada
These speakers contain licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development
Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
(1) These speakers may not cause interference; and
(2) These speakers must accept any interference,
including interference that may cause undesired
operation of the speakers.
These speakers complies with ISED radiation
exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the ISED radio
frequency (RF) Exposure rules. These speakers should
be installed and operated keeping the radiator at
least 20cm or more away from person’s body.
5.15 - 5.35 GHz band is restricted to indoor operations
only.
Data transmission is always initiated by software,
which is the passed down through the MAC, through
the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the
MAC. These are the only ways the digital baseband
portion will turn on the RF transmitter, which it then
turns off at the end of the packet. Therefore, the
transmitter will be on only while one of the
aforementioned packets is being transmitted. In
other words, this device automatically discontinue
transmission in case of either absence of information
to transmit or operational failure.
Precautions
On safety
• Should any solid object or liquid fall into the rear speaker,
unplug the system and have it checked by qualified
personnel before operating it any further.
• Do not climb on the rear speaker, as you may fall down and
injure yourself, or the rear speaker damage may result.
On power sources
• Before operating the rear speaker, check that the operating
voltage is identical to your local power supply. The
operating voltage is indicated on the nameplate at the
bottom of the rear speaker.
• If you are not going to use the rear speaker for a long time,
be sure to disconnect the rear speaker from the wall outlet
(mains). To disconnect the AC power cord (mains lead),
grasp the plug itself; never pull the cord.
• One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet (mains)
only one way. If you are unable to insert the plug fully into
the outlet, contact your dealer.
• AC power cord (mains lead) must be changed only at a
qualified service shop.
On heat buildup
• Although the rear speaker heats up during operation, this
is not a malfunction. If you continuously use this rear
speaker at high volume, the rear speaker temperature at
the rear and bottom rises considerably. To avoid burning
yourself, do not touch the rear speaker.
On placement
• Do not place the rear speaker near heat sources or in a
place subject to direct sunlight, excessive dust, or
mechanical shock.
• Do not place metal objects other than a TV around the rear
speaker. Wireless functions may be unstable.
• If the rear speaker is being used in combination with a TV,
VCR, or tape deck, noise may result and picture quality may
suffer. In such a case, place the rear speaker away from the
TV, VCR, or tape deck.
• Use caution when placing the rear speaker on a surface
that has been specially treated (with wax, oil, polish, etc.),
as staining or discoloration of the surface may result.
• The speakers of this rear speaker are not of magnetically
shielded type. Do not place magnetic cards on the rear
speaker or near it.
If you encounter color irregularity on a
nearby TV screen
Color irregularities may be observed on certain types of TV
sets.
On cleaning
Clean the rear speaker with a soft, dry cloth. Do not use any
type of abrasive pad, scouring powder, or solvent such as
alcohol or benzine.
If you have any question or problem concerning your system,
please consult your nearest Sony dealer.