Loading ...
Loading ...
Loading ...
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you troubleshoot the product.
To replace the blade [ Fig. T1 ]:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged,
bent, out of balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade for 300R: Art. FLY 085
• FLYMO replacement blade for 340R: Art. FLY 086
• FLYMO replacement blade for 380R: Art. FLY 088
1. Unscrew the blade bolt.
2. Remove the blade bolt and the washer.
3. Remove the blade and the spacer.
4. Put the spacer and the new blade on the mower.
5. Put the washer on the blade bolt.
6. Screw the new blade tight with the blade bolt
(tightening torque is 15 – 20 Nm).
Problem Possible Cause Remedy
Mower does not start Mains cable is disconnected
or damaged.
v Connect the mains cable or
if necessary let it be replaced
by an authorised specialist
dealer or the FLYMO Service.
Motor is blocked. v Remove the obstacle.
Start again.
Engine is jammed and
makes a noise
Motor is blocked. v Remove the obstacle.
Start again.
Cutting height is too low. v Raise the cutting height.
Loud noises, the mower
is rattling
Screws on engine, its fixing
or on the mower chasing are
loose.
v Let the screws be tightened
by an authorised specialist
dealer or the FLYMO Service.
Mower runs unevenly or
vibrates strongly
Blade is damaged / worn or the
blade mounting is released.
v Replace the blade.
Blade is very dirty. v Clean the blade.
Lawn is not cleanly mowed Blade is blunt or damaged. v Replace the blade.
Cutting height is too low. v Raise the cutting height.
NOTE: For any other malfunctions please contact the FLYMO Customer Service.
Repairs must only be done by FLYMO service departments or specialist dealers
approved by FLYMO.
7. TECHNICAL DATA
Electric Lawnmower
Unit Value
EasiStore 300R
Value
EasiStore 340R
Value
EasiStore 380R
Rated power W 1200 1400 1600
Mains voltage V (AC) 230 230 230
Mains frequency Hz 50 50 50
Speed of rotation cutting
blade
R/min 3700 3350 3500
Cutting width cm 30 34 38
If possible, only cut the grass when it is dry, if the grass is damp,
the cutting pattern will be uneven.
Rear Roller:
For lawnmowers fitted with a rear roller, it is possible to create a striped
effect on the lawn. For the best stripe results, we recommend cutting on
the lowest possible cutting height suited to your lawn. The stripe effect
will fade in time between cuts.
Transport position [ Fig. O9 ]:
The easy transport position provides additional mobility due to its upright
driving position. Easy to get on and off the lawn at any distance.
1. Attach the grass box to the switch box (see 5. STORAGE).
2. Pull the mower to and from the lawn when it is set in the storage
position.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
2. Clean the underside, the blade and the discharge opening
with abrush (do not use sharp objects).
To clean the overside of the mower and the grass box:
1. Clean the overside with a damp cloth.
2. Clean the airflow slots and the grass box with a soft brush
(do not use sharp objects).
5. STORAGE
To put into storage [ Fig. S1 ]:
The product must be stored away from children.
1. Disconnect the mower from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. The cable hooks must both be on the upper handle.
Wrap the cable in a figure of 8.
4. Store the mower in a dry, enclosed and frost-free place.
Easi Storage position [ Fig. S2 ]:
1. Remove the grass box.
2. Set on the highest cutting height.
3. Fold the handle flat and lock it in position 4.
4. Stand the mower upright.
5. Make sure that the grass box is completely empty.
6. Attach the grass box to the switch box with the storage hook.
Make sure that the grass box is completely secured, the storage
function is accomplished.
7. Store the mower in upright position.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
6
Loading ...
Loading ...
Loading ...