Loading ...
Loading ...
Loading ...
12
5. To stop the mower, release the switch lever.
mWARNING! The mower blade will continue to rotate for
a brief period after the unit has been switched o. Do not tilt or
carry the unit while the motor is still running and do not touch
the blade while it is still rotating. Failure to comply could result
in severe personal injury.
Adjusting the Cutting Height
Follow these instructions to adjust the cutting height of the
lawn mower.
mWARNING! Before making these adjustments,
disconnect the power supply to the mower by plugging
out the safety key from the slot, and wait until the rotating
blade has come to a complete standstill. Wearing gloves is
recommended due to the close proximity of the cutting blade.
ALWAYS FOLLOW ALL SAFETY PRECAUTIONS AND
RECOMMENDATIONS LISTED PREVIOUSLY IN THIS
MANUAL.
1. Power o and remove the safety key from the slot.
2. Remove and empty the grass collection bag.
3. Place the lawn mower on its side.
4. The wheel axles can be placed into 3 dierent cutting
heights: low (will cut grass the shortest), medium, and high
(Fig. 15).
3-Position Height Adjustment:
1. Low: 1.18 in. (30 mm)
2. Medium: 1.93 in. (49 mm)
3. High: 2.52 in. (64 mm)
The cutting height tolerance is +/- 5 mm (+/- 0.2 in.).
5. Move all four wheels to the desired cutting height by
pulling back on the rod axle and setting it to the desired
position. Make sure all four wheels are at the same cutting
height position.
NOTE: Set the mower to the highest cutting height when
mowing on uneven ground or in tall weeds.
6. Place the lawn mower back on to its wheels and reattach
the grass collection bag.
7. Insert the safety key into the slot and resume normal use.
Mowing Tips
mWARNING! Inspect the area prior to mowing and
remove all the stones, sticks, wires and other foreign objects
that could be picked up and thrown by the rotating blade.
Failure to comply not only will damage the mower blade, but
can also lead to serious personal injury.
• Be sure to check the mowing blade periodically for signs
of wear and sharpen it at least once per year, as described
in the maintenance section.
NOTE: A sharp blade will greatly enhance the performance
of the mower, especially when cutting tall blades of grass.
• When cutting thick grass, reduce your walking speed
in order to allow for a more eective cut and a proper
discharge of the clippings. For a healthy lawn, always cut
o one-third or less from the total length of the grass.
The average lawn should be approximately 1.5 to 2 in.
(3.8 to 5 cm) long during cool months, and more than 2 in.
(5 cm) long during hot months. If there is growth, the lawn
should be cut in the fall.
• The lawn will look better if it is always cut to the same
height and in alternate directions.
• When crossing any gravelled surfaces, release the switch
bar lever to turn o the mower. The stones can be picked
up and thrown by the rotating blade.
• Set the mower to the highest cutting height when mowing
on uneven ground or in tall weeds.
mWARNING! If you strike a foreign object, stop the motor
and remove the safety key. Thoroughly inspect the mower and
repair any damage before resuming work.
• IMPORTANT! Never open the ejector ap when the grass
collection bag has been detached (to be emptied) and the
motor is still running. A rotating blade can cause serious
injuries!
• Always carefully fasten the ejector ap and grass
collection bag. Switch o the motor before emptying the
grass collection bag. Always ensure that a safe distance
(provided by the length of the long handles) is maintained
between the user and the mower housing. Be especially
careful when mowing and changing direction on slopes
and inclines.
Fig. 15
High setting
Medium setting
Low settingRod axle
Loading ...
Loading ...
Loading ...