Loading ...
Loading ...
Loading ...
4
The optional locking featur
es are designed to prevent unauthorized removal of
the battery or alarm. It is not necessary to activate the locks in single-family
households wher
e unauthorized battery or alarm removal is not a concern.
These CO Alarms have two separate locking featur
es: one locks the battery
compartment, and the other locks the CO Alarm to the mounting bracket.
Y
ou can choose to use either feature independently, or use them both.
Tools you will need: • Needle-nose pliers • Standard Flathead screwdriver.
Both locking featur
es use locking pins, molded into the mounting bracket.
Using needle nose pliers r
emove one or both pins, depending on which locking
features you use.
USING THE LOCKING FEATURES
L
ocking Pin
THE BATTERY COMPARTMENT LOCK
TO LOCK THE BATTERY COMPARTMENT:
Do not lock the battery compartment until you have
activated the battery and tested the battery back-up.
1.
Activate the battery back-up by removing the “Pull
to Activate Battery Back-Up” tab. Push and hold the
test button on the CO Alarm’s cover until you hear
an acknowledge chirp and the alarm sounds:
4 beeps, pause, 4 beeps, pause.
If the unit does not alar
m during testing, DO
NOT lock the battery compartment! Install a new
batter
y and test again. If it still does not alarm,
r
eplace the CO Alarm immediately.
2. Using needle-nose pliers, detach
one locking pin fr
om the mounting
bracket.
3.
Push the locking pin through the
black dot on the label on the back
of the CO Alarm.
TO UNLOCK THE
BATTERY COMPARTMENT:
Once the CO Alarm is installed, you must disconnect it from the AC power
before unlocking the battery compartment.
ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the
CO Alarm is installed before removing it from the mounting bracket. Failure
to turn off the power first may result in serious electrical shock, injury or
death.
1. Remove the CO Alarm from the mounting bracket. If the unit is locked to
the bracket, see the section “To Deactivate the Locking Feature.”
2. Disconnect the power connector by gently prying it away from the back
of the CO Alarm.
3. Insert a flathead screwdriver under the head of
the locking pin, and gently pry it out of the
battery compartment lock. (If you plan to relock
the battery compartment, save the locking pin.)
4.
T
o relock the battery compartment, close the
battery door and r
einsert the locking pin in the
lock.
5. Reconnect the power connector to the back of the CO Alarm, reattach
the CO Alarm to the mounting bracket, and restore the power.
When replacing the battery, always test the CO Alarm before relocking the
battery compartment.
THE MOUNTING BRACKET LOCK
T
ools you will need:
• Needle-nose pliers
• Standard Flathead screwdriver
TO ACTIVATE THE BRACKET LOCK:
1. Using needle-nose pliers, detach one locking
pin fr
om the mounting bracket.
2.
Insert the locking pin into the
lock located on the pivoting
hinge of the battery door
.
3.
When you attach the CO Alarm
to the mounting bracket, the
locking pin’s head will fit into a
notch on the bracket.
TO DEACTIV
ATE THE BRACKET LOCK:
ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the
CO Alarm is installed before removing it from the mounting bracket.
Failure to tur
n off the power first may result in serious electrical shock,
injury or death.
Always discharge the branch circuit before servicing an AC or AC/DC
CO Alarm. First, turn off the AC power at the circuit breaker or fuse box.
Next, remove the battery from Alarms with battery back-up. Finally, press
and hold the test button.
1.
Insert a flathead screwdriver between the
mounting bracket pin and the mounting bracket.
2. Pry the CO Alarm away from the bracket by
turning both the screwdriver and the CO Alarm
counterclockwise (left) at the same time.
TO PERMANENTLY REMOVE
THE BRACKET LOCK:
Insert the flathead screwdriver
between the locking pin and the
lock, and pry the pin out of the lock.
Loading ...
Loading ...
Loading ...