Loading ...
Loading ...
Loading ...
4
1. PREPARE INSTALLATION
Plan where and how the ductwork will be installed. Access to the top of the hood is
preferred for connection of ductwork.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you
are installing. If installing CP34 or CP35 power pack, use 8” round ductwork and if
installing CP37 power pack, use 10” round ductwork. Use 2” metal foil duct tape to
seal duct joints.
The minimum hood distance above cooktop must not be less than 24”. A
maximum of 30” above cooktop is recommended for best capture of cooking
impurities.
Distances over 30” are at the installer and users discretion.
Run 3-wire power supply cable to installation location. Its length should extend at least
4 feet below the bottom of the custom hood.
M
ODELS CP34 & CP35 (SINGLE BLOWER)
OR CP37 (DUAL BLOWER) TYPICAL DUCTWORK
WARNING
!
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer.
Make sure that the following items are included:
- Power Pack
- Accessories: • Baffle filters with handles:
CP34 and CP35: 3 for the 30’’ and 36’’ width models, 4 for the 42’’ width model
CP37: 5 for this 48’’ width model
• 2 Shielded halogen lamps (120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base)
• 8” Round adapter/damper (included with single blower power packs)
• 10” Round in-line vertical damper (included with dual blower power pack)
• 10” Round adapter (included with dual blower power pack)
• Bag of parts including: 1 wire clamp, 2 wire connectors, 4 no. 8 x 3/8” screws, 9 no. 8 x 1/2” chrome plated screws,
10 no. 8-32 x 1/4” screws. If need be, discard extra screws.
Parts sold separately:
Ducts, elbows, wall and roof caps. Refer to page 3 for a complete list of venting options and model numbers.
NOTE: During installation, protect countertop and/or cooktop.
2. INSTALL DUCTWORK AND ELECTRICAL WIRING
Power pack
Roof cap
Wall
cap
HH0101A
8” round duct for CP34 & CP35
or 10” round duct for CP37
8” round adapter & damper
for CP34 & CP35 or
10” round adapter for CP37
24” to 30”
above
cooking surface
8” round elbow for CP34 & CP35
or 10” round elbow for CP37
10” in line
vertical damper for CP37
3. CUSTOM HOOD PREPARATION
WARNING
!
When building a custom hood, always follow all applicable construction codes and standards.
The custom hood must be constructed to fit the size and shape of the CP34, CP35 or
the CP37 power pack models.
See chart and illustration for details.
POWER PACK
MODEL
WIDTH
TOTAL
WEIGHT
RANGE HOOD DIMENSIONS
A* B* C
CP34 AND CP35 30” 33 LB.19
5
⁄16”28
7
⁄16”4
7
⁄8”
36” 37.2
LB.19
5
⁄16”34
7
⁄16”4
7
⁄8”
42” 41.6 LB.19
5
⁄16”40
7
⁄16”4
7
⁄8”
CP37 48” 56.5 LB.22
9
⁄16”46
7
⁄16”5
7
⁄8”
A
B
C
7/8
”
4½”
HD0296A
C
L
12”
3”
REAR
FRONT
* Dimensions A and B include rivets head.
Loading ...
Loading ...
Loading ...