Loading ...
Loading ...
Loading ...
*Certain Models Only ** Certain models only, nozzles may vary according to model
2
GETTING TO KNOW YOUR CLEANER
A. Bag Door Release Latch
B. Cord Rewind Button
C. Parking Slot
D. Exhaust Filter Cover
E. On/Off Button
F. Variable Power Control*
G. Bag Check Indicator
H. Bag Door
I. Main Cleaner
J. Hose
K. Hose Handle
L. Suction Regulator
M. Telescopic Tube
N. Telescopic Tube Adjuster
O. Floor Type Selector Pedal*
P. Carpet and Floor Nozzle (GP) **
P1. Carpet Nozzle (CA) **
P2. Hard Floor Nozzle (HF) **
Q. Pre-motor Filter
R. Pre-motor Filter Frame
S. Exhaust Filter
T. 2 in 1 Accessory
U. Pet Hair Remover Mini Turbo Nozzle*
V. Allergen Remover Mini Turbo Nozzle*
W. Parquet Nozzle*
GETTING TO KNOW YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it locks into position. [1] To
release the hose: simply press the two latches on the hose end and pull.
2. Connect the hose handle to the upper tube end. [2]
3. Connect the tube lower end to the carpet and oor nozzle** or accessories if required. [3]
USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker
[6].
2.
Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster
up and raise or lower the handle to the most comfortable cleaning position [5].
3. Carpet and Floor Nozzle**: Press the oor type selector pedal* on the nozzle to
select the ideal cleaning mode for the oor type.
[4]
Hard Floor – Brushes are lowered to protect the oor.
Carpet – Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the On/Off button on the cleaner main body.
[7]
5. Rotate Variable power rotary knob* to increase or decrease the power. [8]
6. Adjust the suction regulator to the desired level. [9]
7. Switch off at the end of use by pressing the on/off button. Unplug and press the cord
rewind button to wind the power cord back into the cleaner.
8. Parking and storage – The tube can be parked for temporary storage while in use, or in
the storage position when not in use. [10]
CLEANER MAINTENANCE
Replacing the Dust Bag
If the bag check indicator is red, please check and, if necessary, replace the bag.
1. Lift the bag door Latch to open the bag door and remove the bag [11,12]. The full
dust bag should be disposed of correctly and carefully.
2. Fold a new bag as shown on the bag and t by inserting the collar into the bag
holder.
3. Close the Bag door.
REMEMBER: The bag check indicator may be red if an obstruction has occurred. In this
case refer to ‘Removing a Blockage From the System’.
Cleaning the Filter:
To maintain optimum performance of your cleaner, please wash the pre-motor lter and
exhaust lter after each 5 bag changes.
Cleaning the pre-motor lter:
1. Lift the bag door release latch to open the bag door and remove the bag.
[11,12]
2. To remove the pre-motor lter slide the pre-motor lter frame from the cleaner. [13]
3. Remove the lter from the holder. [13]
4. Wash it in hand warm water [16], and allow it to dry [17] thoroughly before replacing
to the cleaner.
Cleaning the exhaust lter:
1. The remove the exhaust lter, unclip the exhaust lter cover and remove the exhaust
lter pack. [14,15]
2. Wash the lter in hand warm water [16] and allow it to dry
[1
7] thoroughly before
replacing to the cleaner.
REMEMBER: Do not use hot water or detergents. In the unlikely event
of the lters becoming damaged, t a Genuine Hoover replacement.
Do not try and use the product without a dust bag or lter tted.
Cleaning the permanent cloth dust bag* (certain models only)
To maintain optimum performance we recommend that you wash the permanent cloth
dust bag under hand warm water after every 5 full bags. Remove excess water and leave
to dry fully before replacing.
Removing a blockage from the system
If the bag check indicator is red:
1. Check if the bag is full. If so refer to ‘Replacing The Dust Bag’.
2. If it is not full, then;
A.
Do the lters need cleaning?
If so refer to ‘Cleaning the Filter’.
B. Check if there is any other blockage in the system - Use a rod or a pole to
remove any blockage from
telescopic tube* or exible hose.
WARNING*: -The bag check indicator will remain red if the cleaner is used when the bag is
Loading ...