Loading ...
Loading ...
Loading ...
3
deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal. [1Y]
Hard Floor Nozzle* – For parquet oors and other delicate oors. [1Z]
IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides
and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is
rotating.
CLEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
IMPORTANT: To maintain optimum performance, do not allow the dust to sit higher than
the max level.
1. Release the dust container by sliding the dust container release button towards the
front of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Before emptying the Dust Container, gently tap it against the side of a bin to release
any excess dust from the lter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and
use the other hand to press the Dust Container Flap Opening Button to release the
dust into the bin. [15]
4. Close the Dust Container Flap and ret the Dust Container to the cleaner main body.
Cleaning the washable lters
The cleaner is tted with a pre-motor and exhaust lter. To maintain optimum cleaning
performance, regularly clean the lters. Remove excess dust from the lters by gently
tapping them against the side of a bin. The lters should be washed after every 5
container empties.
IMPORTANT: All bagless cleaners require regular lter cleaning. Failure to clean
your lters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
IMPORTANT: Regularly check and maintain the lters by following the lter
maintenance instructions, it is also recommended that you purchase new lters
after every 3rd lter wash. This will maintain your cleaners performance.
To access the Pre-Motor lter:
1. Empty the Dust Container as described in ‘Emptying the Dust Container’. Then,
keeping the Dust Container Flap open:
2. Remove the pre-motor lter by rotating it clockwise at the bottom of the Dust
Container. [16]
3. Separate the protective mesh from the lter. [17] Gently tap both the protective
mesh and the lter against the side of a bin to remove excess dust and wash both
of them under warm water. [18] Do not use hot water or detergents.
4. Remove excess water from the lter and leave it to dry fully before reusing. [21]
5. Once the lter is fully dry, reassemble the lter pack (protective mesh and lter) and
ret to cleaner.
IMPORTANT: Do not use the product without the pre-motor lter pack tted.
IMPORTANT: Always ensure the lter packs are fully dry before use.
To access the exhaust lter:
1. Unclip the exhaust grid from the rear of the cleaner. [19]
2. Separate the lter from the grid and wash the lter under warm water. [20] Do not use
hot water or detergents.
3. Remove excess water from the lter and leave to dry fully before reusing. [21]
4. Remount the lter into the grid and ret it to the cleaner.
REMEMBER: Do not use hot water or detergents. In the unlikely event of the lters
becoming damaged, t a Genuine Hoover consumable. Do not try and use the product
without a lter tted.
Removing a blockage
1. Check if the dust container is full. If so refer to ‘Emptying the Dust Container’.
2. If the dust container is empty but suction is still low:
A. Do the lters need cleaning? If so refer to ‘Cleaning the Washable Filters’.
B. Check if there is any other blockage in the system - Use a rod or pole to remove
any blockage from the extension tube or exible hose.
C. Check if pre-motor lter is tted and lter door is closed
Warning (Certain models only*) - If the cleaner is used for a signicant period of time
with a blockage, a thermal cut out will switch the cleaner off to prevent overheating.
The bag check indicator turn green once the cleaner has switched off to signal that the
thermal cut out has been activated. If this should happen, switch the cleaner off, unplug
and correct the fault. It will take about 45 minutes for the cut out to automatically reset.
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist
before calling your local Hoover service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the Bag over-lled? Please refer to ‘Cleaner Maintenance’.
• Is the lter blocked? Please refer to ‘Cleaner Maintenance’.
• Is the hose or nozzle blocked? Please refer to ‘Removing a Blockage’.
*Certain Models Only ** Certain models only, nozzles may vary according to model
Loading ...