Loading ...
Loading ...
Loading ...
Adjustable and delayed self-switching off
Causes total shutdown of lights and aspirator.
With the hood in operation, select the desired speed, then keep the TL button pressed for a few seconds until the speed LEDs (L1, L2, L3, L4) start
flashing indefinitely until the hood auto-off setting. By pressing one of the keys (T1, T2, T3, T4) the delayed auto-off time can be programmed, as
follows:
T1 corresponds to 5 minutes; T2 corresponds to 10 minutes; T3 corresponds to 15 minutes; T4 is 20 minutes.
During automatic shut-off operation, the set speed can be changed. If the choice of the switch-off time corresponds to the set speed, the speed LED
flashes; if the choice is different, the speed LED remains fixed.
During operation with auto-switch-off it is possible to deactivate the delayed switch-off by keeping the hood in operation, keeping the button
corresponding to the selected delayed time pressed.
During the auto-off function it is however possible to switch off the hood by pressing T1 twice.
Maintenance warning for grease filters
Every 30 hours of operation of the hood, when it is switched off, all the LEDs of the hood speed buttons will light up for 30 seconds to alert the
necessary cleaning of the metal grease filter. To reset the timer simply press and hold the T4 button with the fan off. If the timer is not reset, all the
LEDs will light up again each time the hood is switched off again. You can reset the timer at any time.
Charcoal filters maintenance alert (for hoods in the filtering version)
Every 120 hours of operation of the hood, when it is switched off, all the LEDs of the hood speed buttons will light up for 30 seconds to remind the
cleaning of the metal grease filters and, if the hood is in the filtering version, it is necessary to replace the carbon filters. To reset the timer, simply
press the T4 button with the fan off, otherwise the LEDs will flash again after each time the hood is switched off. You can reset the timer at any time.
MAINTENANCE
Always disconnect the hood from the mains before carrying out any maintenance or cleaning operation.
Particular attention should be paid to the metallic anti-grease filters that are designed to trap particles of fat contained in the fumes. The metallic anti-
grease filters must be washed at least once a month or, if present in this model, when indicated by the electronic notice, with detergent in hot water
(or in the dish-washer). The filters may discolour after a few washes. This is normal and does not mean they have to be replaced. To remove the
metal grease filters, use the handle (Fig. 2). It is recommended to refit the metal grease filters only if perfectly dry.
ATTENTION: the grease collected in the filters can easily catch fire and it is therefore extremely important to clean the metallic filters on a regular
basis as per instructions.
The activated charcoal filters, if present, are designed to collect unpleasant odours in the cooking fumes. The air is then released purified in the
environment. The charcoal filters must not be washed, but replaced 2 or 3 times a year, depending on how much the hood is used. New filters are to
be requested directly to the manufacturer.
To replace the activated carbon filters, first remove the metal anti grease filters (Fig. 2). At this point the activated carbon filters can be removed by
rotating them about 90° from their position to release them from the interlocking tabs, then accompanying the filter downwards, without the use of
tools.
To reinstall the new activated carbon filters, reverse operations.
The hood features a LED light that, in addition to offering a good lighting and a significant energy savings, are guaranteed to last on average 10
times more than traditional lights. For replacement, contact the Assistance Service.
In order to remove the remaining glue or any impurity, the cooker hood must be cleaned immediately after installation and after having removed the
protective film.
The cooker hood must be cleaned frequently both internally and externally (at least once a month).
Do not let dirt gather on the inner and outer surfaces of the hood.
To clean the exterior of the hood do not use either acid or basic products, or abrasive sponges.
Clean the hood with a sponge dampen in warm water and a little quantity of neutral detergent (for example dishwasher detergent), in order to remove
possible particles of grease.
Rinse with a damp cloth, removing all the detergent carefully, following the satin finish direction on the steel surface.
Drying is very important, especially in areas where water is particularly hard and leaves limestone.
All the ordinary and extraordinary maintenance can be performed without having to remove the hood.
Fig. 1A
Fig. 3
Fig. 4
Fig. 2
Fig. 1F