Loading ...
GENERAL INFORMATION
ASSEMBLY OF THE HIGH CAPACITY VACUUM
1. Remove all parts from the shipping container.
2. Filter is shipped already attached to motor bulkhead.
3. Insert either end of the hose into the vacuum intake. Any accessory may be used at this time.
4. Insert detachable power cord into the vacuum head and insert other end into the grounded wall outlet.
5. The High Capacity Vacuum is now ready for use.
6. Assemble roller base and use for extra mobility.
FILTER REPLACEMENT
1. Remove power cord from power source.
2. Unfasten retaining clips (3) from vacuum head. Lift vacuum head off of the filter.
3. Place filter lid securely on the filter. The filter is now ready for disposal.
4. Apply new filter below vacuum head and fasten (3) retaining clips.
5. Plug the power cord in the power source.
6. Dispose of the filter cartridge in an appropriate manner compliant with all local, state, and federal
laws.
NOTE: These vacuums have a factory installed resettable Thermal Cutout (TCO) for added operator and motor safety. If the unit gets too hot, the vacuum will
shut down for approx. 20 minutes. Turn the on/off switch to the off position, and turn back on in approximately 20 minutes. Your hose may be clogged, or it may
be time to install a new filter.
WARRANTY
WARRANTY SERVICE INFORMATION: For warranty service information, please contact your
local distributor. Warranty period for the High Capacity Series is 18 months. When using the standard
Atrix filter for removing toner, developer, dirt, dust and other NON-hazardous waste, the vacuum can be
serviced. When using the Atrix HEPA filter for removing lead or other hazardous waste, the vacuum
CANNOT be serviced. Field replacement parts will be made available to the user for the duration of the
warranty period. This warranty is in lieu and exclusive of any warranty of merchantability, and/or quality,
and any application for use for a particular purpose. No other warranties expressed or implied are granted or
acknowledged by Atrix International.
EXCLUSIVE TO WARRANTY: Accessories, filters, motor brushes, and damage to the vacuum caused by accident, misuse or negligence are not covered by the
above warranty. Filters and replacement filters are intended for single use only. Attempting to re-use the filter by dumping the contents may cause
damage to the vacuum, and will void the warranty. Atrix shall not be liable for special or coincidental damages such as loss of other property or equipment, loss
of revenue, personal injury, death or inconvenience, but not limited to the above examples. Atrix assumes only liability for the cost of its vacuum systems and what
is expressly stated in this warranty.
Standard Replacement Parts
Vacuum Head (Power Unit) 421-000-100 (120 Volt)
421-000-101 (230 volt)
Filter Replacement, toner, developer, dust and dirt-5 Gallon 421-000-002
Filter Replacement, HEPA-5 Gallon 421-000-005
Detachable Power Cord 10’ office machine end, 110V 31651
ESD Safe Round Dusting Brush 31653
8’2” European Power Cord, 230V 66021A
8’2” U.K. Power Cord, 230V 66097A
Vacuum Roller Base 421-000-105
Toner proof Stretch hose, 10’ ESD Safe 31671
Toner Proof Stretch Hose, 16’ ESD Safe 31681
Clear Hose, 9’ AVPA009
Hose adapter, connect two hoses for longer length ESD Safe SCHENG600
Utility Nozzle AVPA011
Utility Nozzle Brush AVPA017
Crevice Tool ESD Safe 31654
Crevice Tool Brush, brush that fits in the crevice tool 31652
Rubber Flex Neck, 16” long, angled neck, soft rubber ESD Safe 31657
Foot Switch, for hands free operation (110V only) 420-000-013
Accessory kit, allows user to vacuum floors and large areas ATIVACACC
Includes: (Two 20” straight wands, 11” curved neck, 10” carpet wand,
10” horsehair floor brush, vinyl accessory caddy) Non-ESD Safe
To Register
your Warranty
Visit: www.atrix.com
ATRIX INTERNATIONAL, INC.
1350 Larc Industrial Boulevard
Burnsville, MN 55337-1412
Telephone: (952) 894-6154
(800) 222-6154
Fax: (952) 894-6256
Manual: 999403
E-mail: Sales@Atrix.com