Loading ...
Loading ...
Motion sensitivity – amount of motion
required to turn on the light
MODE: TO SET:
High
Medium
(DEFAULT)
Low
Getting to know your new Z-Wave device
The smart motion switch has the following default settings:
• Occupancy mode — The connected light automatically turns on when motion is
detected and turns off when no motion is detected. The sensor must detect no motion
for 20 seconds before activating automatic turn off.
• 5-minute time-out — the connected light will turn off 5 minutes after motion
has stopped.
• Light-sensing mode — this mode is disabled. Motion will always turn on the
connected light.
• Motion sensitivity is set to medium.
To change any of the above settings, see programming options (Section 4).
The smart motion switch has the following features:
• Turn ON/OFF manually or remotely via the Z-Wave controller.
• Blue LED indicates programming confirmation.
• Can be included in multiple grounps and scenes.
• Interchangeable buttons - white and light almond included.
• May be used in single-pole installation or with up to two GE-branded Add-on Switches
in 3-way or 4-way wiring configurations.
• Compatible with all incandescent, xenon, halogen and CFL/LED bulbs.
• Uses a standard, decorative-style wallplate for single-gang installations
(wallplate not included).
• This Z-Wave device has advanced features that allow you to customize your
experience. These features can be adjusted by a Z-Wave enabled controller that
supports the Z-Wave configuration command class. For a complete list of adjustable
configurations, visit www.ezzwave.com/config.
Adding your device to a Z-Wave network
1. Follow the instructions for your Z-Wave certified
controller to include the smart switch to the
Z-Wave network.
2. Once the controller is ready to include your smart
switch, press and release the top or bottom button
on the smart switch to include it in the network.
Please reference the controller’s manual for
instructions.
Now you have complete control to turn your light
ON/OFF according to groups, scenes, schedules
and interactive automations programmed by your
controller. If your Z-Wave certified controller features
remote access, you can now control your lighting
from your mobile devices.
To exclude and reset the device
1. Follow the instructions for your Z-Wave certified
controller to exclude a device from the Z-Wave
network.
2. Once the controller is ready to exclude your device,
press and release the top or bottom button on the
smart switch to exclude it from the network.
To return to factory defaults
Press and release the top button 10 times within 5
seconds. The LED will flash 3 times quickly confirming
change.
Note:
This should only be used in the event your
network’s primary controller is missing or otherwise
inoperable.
PROGRAMMING OPTIONS
Many controllers will offer programming changes through the application. Programming changes can also be made directly at the switch through simple button presses.
To program the device manually, refer to the diagram shown above in Section 2 and follow the instructions as displayed below. Programming capabliities vary based on
program and connected device.
Time-out duration – amount of time the
light stays on after motion stops
MODE: TO SET:
5 sec
1 min
5 min
(DEFAULT)
15 min
30 min
Note: Continue to hold button until LED cycles to flash the
correct number of times. Time-out duration does not apply in
manual mode.
Press & hold
GUIDE:
Flashing LED
MODE: LIGHT ON WHEN: LIGHTS OFF WHEN: TO SET:
Occupancy
(DEFAULT)
Automatic Automatic
Vacancy
Press & release
top button
Automatic
Manual
Press & release
top button
Press & release
bottom button
Occupancy – Light turns on automatically with motion and off automatically without motion
Vacancy – Light turns on manually and off automatically without motion
Manual – Light only turns on and off manually
1.
To change color of the buttons
This step is optional. Before installation, you may
want to change the color of the buttons to match
your wallplate or décor.
1. Pinch both tabs down to release
button.
2. Lift the button up and off.
3. Put the new button onto the switch
by inserting the tabs near the
motion sensor first and the tabs on
the opposite side last.
4. Repeat steps 1 and 2 for the button
on the other side.
Once this step has been completed
please return to section 3.
A
DB
C E
F
G
H
I
J
K
A. Ground (Green/Bare)
B. Load (Black)
C. Line (Black)
D. Traveler (Red/Other)
E. Neutral (White)
F. Top Button — press & release to turn the
switch on
G. Bottom Button — press & release to turn the
switch off
H. Configuration Button — changes the
operation mode of switch
I. Motion Sensor
J. Blue LED (behind cover) — indicates
programming confirmation
K. Air Gap Switch — pull the air gap switch out
to disconnect the power. Push it all the way
back in for normal operation.
Screw terminal installation requires wiring
connections for line (hot), load, neutral and
ground. Traveler wire required for 3-way or
4-way installation.
Light sensing – motion sensor only turns light on if
room is dark
MODE: TO SET:
On
Off
(DEFAULT)
Light sensing does not apply in vacancy or manual modes.
1.
1.
2.
4.
5. 6.
Loading ...
Loading ...
Loading ...